Académique Documents
Professionnel Documents
Culture Documents
Australian Standard
This is a free 4 page sample. Access the full version at http://infostore.saiglobal.com.
FLUID POWER—HYDRAULIC
AND PNEUMATIC CYLINDERS—
BORE AND ROD DIMENSIONS
This Australian standard was prepared by Committee ME/35, Fluid Power Systems and
Components. It was approved on behalf of the Council of the Standards Association
of Australia on 7 November 1985 and published on 6 January 1986.
Review of Australian Standards. To keep abreast of progress in industry, Australi an Standards are subject
to periodic review and are kept up to date by the issue of amendments or new editi ons as necessary. It is
important therefore that Standards users ensure that they are in possession of the latest edit ion, and any
amendments thereto.
Full detail s of all Australi an Standards and related publications wil l be found in the Standards Australia
Catalogue of Publications; this information is supplemented each month by the magazine ‘The Australian
Standard’, which subscribing members receive, and which gives detail s of new publi cati ons, new edit ions
and amendments, and of withdrawn Standards.
Suggesti ons for improvements to Australian Standards, addressed to the head offi ce of Standards Australia,
are welcomed. Noti fi cati on of any inaccuracy or ambiguity found in an Australi an Standard should be made
without delay in order that the matter may be investigated and appropriate action taken.
Australian Standard
This is a free 4 page sample. Access the full version at http://infostore.saiglobal.com.
FLUID POWER—HYDRAULIC
AND PNEUMATIC CYLINDERS—
BORE AND ROD DIMENSIONS
PREFACE
This edition of this standard was prepared by the Association’s Committee on Fluid
Power Systems and Components, to supersede AS 2019—1977, Hydraulic and
Pneumatic Cylinders.
This edition differs from the previous edition in the following respects:
(a) A new table (Table 3) covering piston strokes has been added.
(b) The table dealing with piston rod thread end dimensions (Table 4) has been
amended, the pitches having been added to thread designations M36 to M110
inclusive.
(c) The table dealing with piston rod female thread end details (Table 5) has been
amended. It now has one series of values for e min. and the two series of values
of f 1 min. The two series of values for f 2 max. have been replaced by two series
of values for f 1 .
(d) The table dealing with piston rod male shouldered and unshouldered thread end
details (Table 6) has been amended. The series of values for f 1 min. and the two
This is a free 4 page sample. Access the full version at http://infostore.saiglobal.com.
series of values for f 2 max. have been replaced by two series of values for f 1.
(e) All references to nominal pressures have been eliminated.
CONTENTS
Page
SPECIFICATION
1 Scope . . . . . . . . . . . . . . . .. . .. .... . . . .. . . . . ... . . . . . . . .. .. . 3
2 Definition . . . . . . . . . . . . ... .. .... . . . .. . . . .... . . . . . . . .. .. . 3
3 Referenced Documents . . .. .. . .. .. . . . .. . . . .. .. . . . . . . . .. .. . 3
4 Cylinder Bore . . . . . . . . . .. ... .. .. . . . .. . . . .... . . . . . . . .. .. . 3
5 Piston Rod Diameter . . . . .. ... .. .. . . . .. . . . .... . . . . . . . .. .. . 3
6 Piston Rod Threaded Ends .... . . ... . . . .. . . . .... . . . . . . . .. .. . 3
7 Provision for Tightening . ... .. ... . . . . .. . . . ... . . . . . . . . .. .. . 3
8 Piston Strokes . . . . . . . . . ..... .. .. . . . .. . . . .. .. . . . . . . . .. .. . 3