Académique Documents
Professionnel Documents
Culture Documents
-0-
Table of Contents
Important Safety Notice 01 02 03 04 05 06 07 .........................................................................................01
Product Specification ..........................................................................................03 Flat Panel Specification .......................................................................................13 Exploded Diagram ..............................................................................................27 Troubleshooting ....................................................................................................32 Spare Parts List ...................................................................................................35 Schematics and Layouts.......................................................................................36 Assembly and Disassembly ................................................................................38
2.
Many electrical and mechanical parts in this chassis have special safety visual inspections and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Before replacing any of these components read the parts list in this manual carefully. The use of substitute replacement parts, which do not have the same safety characteristics as specified in the parts list, may create shock, fire, or other hazards.
3.
Service notes
When replacing parts or circuit boards, clamp the lead wires around terminals before soldering. Keep wires away from high voltage, high temperature components and sharp edges. Keep wires in their original position so as to reduce interference. Adjustment of this product please refers to the user manual.
01 Product Specification
1. General:
Acer V 193W is designed with LVDS interface and dual (analog and digital signal) input, it featured with embedded universal AC power supplies and audio input. Its a green product and meets all ROHS standard. The power button and display control buttons are on the front of the monitor. The monitors shall automatically to display lower resolution video modes into 1440x900 full screen display. The image can be adjusted through OSD control.
Specifications
1.2 Accessories
Items Description VGA cable
1.8m
DVI cable
1.8m
Users manual
Multi
Warranty card
English
2. Operation Specifications
The unit should suffer no visible cosmetic damage and should operate with no degradation in display quality during exposure to the operating conditions and after exposure to the non-operating conditions, in any sequence.
Specification
Storage
Temperature range Relative humidity Altitude -25C to 60C 5% to 80% 0 to 9144M (30000 ft)
2.2 Safety, EMC, Ergonomics and Compatibility Requirements Items Safety EMC Ergonomics Compatibility Power Management UL/cUL
Description CB
TUV/GS
CCC
Other
FCC
CE
CCC
VCCI-B
TCO99
TCO03
Windows 2000
Windows XP
vista
2.4 Reliability
Items
MTBF CCFL Life time Luminance becomes 50%
Condition
Spec
40,000 Hours 40,000 Hours(min)
Note
Excluding the LCD, CCFL Note1
Note1. Display an all WHITE field at mid Brightness and Contrast settings.
AC Input Voltage Range AC Input Current AC Frequency Range Inrush Current Regulator Efficiency Ripple and Noise DC Output Voltage and Current Power consumption Protection Power management Note2.
Universal input full range 100Vac 240Vac 100Vac 240Vac 100Vac,cold star,25C 240Vac,cold star,25C DC output full loading +16V output +5V output VCC16V(15.2~18V) VCC5V(4.95~5.45V) with Audio
100~240VAC /50~60Hz 1.2A(max) 0.6A(max) 50Hz 60Hz 40A (max) 60A(max) 75% <500mv <150mv 1.6A(typ.),2.0A(max) 1.1A(typ.),1.5A(max) 45W See Table-1 See Table-2
See Note2
Before each test, the buck capacitor need to be discharged. Before each test, it must be 10 minutes at least after the latest test.
Table-1 Protection OPP(Over power protection) SCP(short circuit protection) Condition nominal AC input with auto-recovery function Spec 50W ( min )
Table-2 Status Power On Power Saving Power Off H-sy nc on off on off -V-sy nc on on off off -Video active blanked blanked blanked -Power 45W < 2W < 2W < 2W < 1W LED BLUE Amber Amber Amber Off
Items
Lamp Input Voltage Input current On/Off switch level Brightness PWM duty CCFL operating Voltage CCFL Current
Specification
4 CCFL 15.2V~18V 1.6A (Typ.), 2.0A (Max.) 5.5VVon 2.0 V (on) -0.3v Voff 0.8 V (off) 35%~100% PWM:High=3.3V(3.0~3.6V),Low=0.0V 680Vrms (Typ.), 2.0 mA (min.)(With PWM Dim) 7.0mA (Typ.) 7.5mA (Max.) 5
1700 Vrms (0C) 40~80 KHz > 1 second 70%(with dummy load)
INL MT190AW01(V-5) 250 cd/m2 Set brightness control and also contrast control at maximum, to measure the screen center, the light output shall BL cd/m2 (as panel spec)
The test standard conditions refer to Sec 3.3. (Brightness and contrast are under default value)
Items
Analog RGB signal Sync
Condition
Input impedance = 75 Ohm Input impedance 1k Ohm 0.7Vp-p
Specification
TTL level, Separate H/V-sync(+/-)
D-SUB Inputs
Through D-SUB connectors, this unit can support FH= 31.5 ~ 80 KHz, Fv=56 ~ 75Hz and SXGA display modes as below:
VESA MODES
Horizontal
Mode Resolution Total Nominal Frequency +/-0.5KHz 31.469 37.861 37.500 35.156 37.879 48.077 46.875 48.363 56.476 60.023 67.500 60.000 63.981 79.976 55.469 55.935 70.635 Sync Polarity N N N P P P P N N P P P P P P P N N P N N N N P
Vertical
Nominal Frequency +/-1Hz 59.941 72.809 75.000 56.250 60.317 72.188 75.000 60.004 70.069 75.029 75.000 60.000 60.020 75.025 59.901 59.987 74.984 70.087 Sync Polarity N N N P P P P N N P P P P P N N P P Nominal Pixel Clock (MHz)
640*480@60Hz VGA 640*480@72Hz 640*480@75Hz 800*600@56Hz SVGA 800*600@60Hz 800*600@72Hz 800*600@75Hz 1024*768@60Hz XGA 1024*768@70Hz 1024*768@75Hz 1152*864@75Hz 1280*960@60Hz SXGA 1280*1024@60Hz 1280*1024@75Hz 1440*900(Red)@60Hz WXGA+ 1440*900@60Hz 1440*900@75Hz EGA VGA SVGA XGA 720x400@70Hz 640*480@66.7Hz 832*624@75Hz 1024*768@75Hz 1152*870@75Hz XGA SXGA 1024*768@72Hz 1280*1024@70Hz
800*525 832*520 840*500 1024*625 1056*628 1040*666 1056*625 1344*806 1328*806 1312*800 1600*900 1800*1000 1688*1066 1688*1066 1600*926 1904*934 1936*942 900*449 864*525 1152*667 1328*804 1456*915
25.175 31.500 31.500 36.000 40.000 50.000 49.500 65.000 75.000 78.750 108.000 108.000 108.000 135.000 88.75 106.5 136.75 28.322
IBM MODES
31.469
MAC MODES
35.000 49.725 60.241 68.681
66.667
74.550 74.927 75.062
P
N N N N P
30.240
57.283 80.000 100.00
72.086
69.853
78.434
127.000
Note: 1. Non-interlace signals only (An interlace signal cannot be display) 2. Please refer to F/W specification for more detail 3. Each frequency of Power Macintosh and Sun Ultra is a reference value For DVD Player Input, Attached timing is supported: (Optional)
Mode Resolution (active dot) Resolution (total dot) Horizontal Frequency (KHz) Vertical Frequency (Hz) Nominal Pixel Clock (MHz) Remark
DVD Player
4.2.2 4.2.3
Digital signals
TMDS Signal: (min) 200mVpp@24Bit
DDC signals
DDC signals: 5V@50mA TTL level
Condition
Sync polarity: (+) or (-) Sync polarity: (+) or (-) Excluding Horizontal 31.5~80 KHz or Vertical 56-75 Hz
31.5 ~ 80 KHz.
Specification
56-75Hz Message Input Not Supported on screen
cs
cs
Specification
Output power
5. Function Specifications
All the tests to verify specifications in this section shall be performed under the following standard conditions unless otherwise noted. The standard conditions are: Temperature Warm-up time Checking display modes : 25 5C : 30 minutes minimum : All the specified modes
[AUTO]
[MENU]
[], []
[e Color ]
A. When OSD un-displays, press [e Color] to show e Color OSD, and press again the OSD can not disappear, but the time of e Color OSD disappearing is reset 10 second again. B. When OSD disappear not including e Color OSD, press [e Color] to show e Color OSD OSD, the OSD before disappears, but the parameters of it should be saved Power on or power off the monitor Hot Key Operation
[POWER]
5.2.2
e Color
FACTORY MODE
ON
Press [e Color ] & [MENU] at the same time, and then press [POWER] for DC power on. OSD menu will be shown with F on the left top. Select F for entering factory mode.
First
Second
Third
Control Range
Default Value
Brightness
Empowering Technology
50 50 50 60 56 77 44 77 97 77
Contrast
Standard mode Graphics mode Movie mode User mode Text mode
User
Brightness
ACM
Image Focus Clock Horizontal Vertical
OFF
0 ~ 100 0 ~ 100 0 ~ 100 0 ~ 100 Depend on each timing
Position
--------10
50 1 50
Depend on each timing
NO-EMEA English Deutsch Espaol Language Franais Italiano Hor. Position OSD Ver. Position OSD Timeout Input (Dual) Analog Digital
---------------------------
English
50 50 20
-----
DDCCI ON/OFF Input (Analg only) DDCCI ON/OFF Resolution Info H. Freq V. Freq S/N Reset Exit
----ON ON
-----------
-----------
-----
------ETL000.0000(22) -----
6.0
2. Adjust ISP programming Firstly, double click RTDTool_4.6.exe and open ISP program, then select 25XXV/2525L, and RTD 2120 ISP button
12
13
Fifthly, click programbutton as below,then you will see ISP will going on. There will be prompting if programming is OK.
Program button
14
Configure Inform
Programmi ng speed
15
OK
Open ISP program
Flowing chart
OK
Choose manufacturer and
OK LOAD FW files OK
Click program button
OK
Beginning programming
Choose Config and adjust programming
OK
Turn off power if programming is OK
NG
e Color
FACTORY MODE
ON
Press [e Color ] & [MENU] at the same time, and then press [POWER] for DC power on. OSD menu will be shown with F on the left top. Select F for entering factory mode.
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
03 Exploded
3.1. LCD Exploded drawing (All)
Diagram
31
32
33
34
04
4.1 Inverter circuit on power board
LED Green? Yes Backlight cant be turned on. Yes Is there 5Vdc voltage on pin2 of IC501? Yes Is there high-level voltage on pin8 of IC501? No No
Troubleshooting
Is Ok R517?
Yes
Yes Are connected rightly CN501, CN502, CN503 and CN504? Yes No
No
Is there instantaneously pulse wave on pin1, pin3, pin15 of IC501 at the moment of restart?
No
Is Ok IC501? No
Yes
END
35
4.2
power
board
No power
Check IC802,Q804
END
36
37
05
Level 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Inl P/N
PCBA,I/F 791401300600R BOARD(V5,EMEA,W/O),LE19D0PCBA,P/I BOARD,W/O 791401401600R SPK,LE19D1-612 ROHS PCBA,KEYPAD BOARD,LE9D0791401500000R 612 ROHS PWR CORD 16A/250V BLK 6FT 453070800210R VDE H05VV-F 3G CABLE,D-SUB 15P MALE 6FT 453010100380R BLACK/BLUE, ROH CABLE,DVI-D 18+1P MALE 6FT 453030300370R BLACK , ROHS HRN ASSY 2x4P 55mm 430300801670R UL1571#28,ROHS HRN ASSY 2x4P to 8P 215mm 430300801680R UL1571#28,ROHS HRN LVDS FFC 30P 182mm 430303001500R ROHS ASSY, BEZEL,SLIVER,INL 714030015600R V5 LE19D1 714020013100R ASSY,BASE,BLACK,LE19D1 714011202300R ASSY,STAND,BLACK,LE19D1 COVER HINGE,BLACK 501020220020R RIGHT,LE19D1 COVER HINGE,BLACK 501020220021R LEFT LE19D1 BACK COVER,ALL,BLACK,INL 501020220000R V5 ,LE19D1 ASSY,CHASSIS,V,ALL,INL V5 701000007100R ,LE19D1 LCP 19" MT190AW01-V5631102091401R G1,AM1900004511(IN
38
39
40
S1
Place panel
(1).Take panel out of box and place it on the foam. (2).Tear open the PE bag and put it in the LCP 19" designated carton. MT190AW01-V5(3).Place panel on the foam like the attached 631102091401R G1,AM1900004511( picture. IN Remark:Do not touch the lamp cord and place the surface of panel downsides on the cushion.
S2
HRN ASSY 2x4P 1.Check if the keypad and relevent wire you to 8P 215mm choose are OK. 430300801680R UL1571#28,ROH 2.Insert the wire into the keypad like the S Picture
S3
1.Check if there is any lacquer missed or ASSY, sctratch happened to the front bezel. 714030015600R BEZEL,SLIVER,INL 2.Insert the fixed keypad into the front bezel V5,LE19D1 as picture
41
S4
S5
S6
Place the chassis on the cushion after check,like the attached Picture
42
S7
Insert powerboard into the designated location of chassis ,like the attached Picture
S8
Connent powerboard with the relevant PIN in the mainboard like the attached Picture
S9
43
4
Fix 6 pcs of screws separately on the poweboard and mainboard like the attached Picture1 SCREW ,P,CRO 509146306200 SS,W /W AS,M3* R 6,Zn-Cc
S10
S11
Paste FFC wire on the disignated location like the attached Picture
S12
(1). Handle hexagonal screws and electric opener (2). Twist screw in the interface like the attached Picture1. (3). Place cushion on the designated location after iron frame is taken away.
44
S13
F ix c h a ssis
A S S Y ,C H A S S IS ,V ,A L L ,IN L V 5 ,L E 1 9 D 1
S14
In se rt F F C c a ble
1 .Tear off th e ad h en s ive tap e of F F C w ire; 2 .In s ert F F C w ire in to th e in terfac e of p an el 3 .P u t F F C wire in ord er an d p as te th em on th e p an el 4 .F ix c h as s is on th e b ac k of p an el
1 )In s ert 4 p c s lig h t w ire in to th e relevan t p os ition 2 ) p u t th e b alan c e lig h t w ire to th e p os ition as p ic tu re
S16
In se rt ke ypa d C a b le
1 )In s ert k eyp ad w ire in to th e relevan t P IN in th e k eyp ad 430300801680 2 )F ix b u tton on th e relevan t p os ition of R as s em b le 3 )C on firm if k eyp ad is in s erted p rop erly
45
S17
F ix back cover
501020220000 R
S18
F ix stand
1 2
3 4
714011202300 R
A S S Y,S TA N D ,B L A C K ,L E 1 9 D 1
S19
C h eck if b ase is q u alified an d in sert it in to 714020013100 th e relevan t location p rop erly like th e R attach ed P ictu re
A S S Y,B A S E ,B L A C K ,L E 1 9 D 1
S20
P acking
46