Académique Documents
Professionnel Documents
Culture Documents
Contents
Tunnel Junctions and applications of tunneling 1. Tunneling through a potential barrier 2. Potential Energy profiles of material interfaces 3. Applications of Tunneling Coulomb Blockade and Single Electron Transistor 1. Coulomb Blockade 2. Single Electron Transistor
12
13
Applications of tunneling
Field Emission
MOSFETs Scanning Tunneling Microscope Double Barrier Tunneling and Resonant Tunneling Diode
Field Emission
Fowler-Nordheim Tunneling
Tunneling is the process by which current can flow from lead to lead through quantum dot. Quantum dot which is merely a very small material region, is also called quantum island or coulomb island. We will model the quantum dot and exterior leads using the classical concept of capacitance, and consider electron conduction via tunneling, and so we use a mixed classical- quntum model. As we will see the most fundamental effect in nanoelectronics is related to the significant change in energy when a single electron is transferred into a nanoscopic material region , such as, a quantum dot is known as coulomb blockade.
Assuming square capacitor plates of length L, and for convenience assume d= L/10 Then to observe coulomb blockade we must have
L<< 70nm
(15)
If rather having a single electrons tunnel, assume that n electrons tunnel a group , i.e., it can be easily shown that
replace the expressions derived previously for the single charge. Equating the charging energy to the thermal energy we have
TUNNEL JUNCTIONS
The tunneling that occurs across can be accounted by
considering the capacitor to be a leaky capacitor modeling by an ideal capacitance in parallel with a resistance
Rt = V/I
Where V is the DC voltage applied at the junction and I is the resulting current due to tunneling. This tunneling resistance is not an ordinary resistance, but conceptually allows electrons to cross the insulation junction as discrete events. The parallel combination of capacitor and tunneling resistance is called a tunneling junction.
TUNNEL JUNCTIONS
degree, we can get an estimate of this by considering the uncertainty relation between time and energy, E t /2 Time constant of parallel RC circuit is = RC Then = RtC is a characteristic time associated with tunneling. This is not the time to tunnel through the junction, but, rather the time between the tunneling events. is considered to be the approximate lifetime of energy state of the electron on one side of the barrier. Thus we have uncertainty in energy E / (2RtC) To observe the Coulomb Blockade effect, the charging energy must be much larger than this uncertainty, such that
Tunneling from the lower to the upper plate can occur (since Coulomb Blockade is then thwarted) this results the decrease in the +ve charge on top plate And the increase of ve charge on the bottom plate
functioning It consists of two electrodes known as the drain and the source, connected through tunnel junctions to one common electrode with a low selfcapacitance known as the island. The electrical potential of the island can be tuned by a third electrode, known as the gate, capacitively coupled to the island.
Working
A key point is that charge passes
through the island in quantized units. For an electron to hop onto the island, its energy must equal the coulomb energy e2/2C. When a positive voltage is applied to the gate electrode the energy levels of the island electrode are lowered.
61
Working
When both the gate and the bias
voltages are zero, electrons do not have enough energy to enter the island and current does not flow. As the bias voltage between the source and drain is increased, an electron can pass through the island when the energy in the system reaches the coulomb energy. The critical voltage needed to transfer an electron onto the island equal to e/C, is called the coulomb gap energy
62
Working
(a)When a capacitor is charged through a resistor, the charge on the capacitor is proportional to the applied voltage and shows no sign of quantization. (b) When a tunnel junction replaces the resistor, a conducting island is formed between the junction and the capacitor plate. In this case the average charge on the island increases in steps as the voltage is increased (c)The steps are sharper for more resistive barriers and at lower temperatures.
63
Here n1 and n2 are the number of electrons passed through the tunnel barriers 1 and 2 n = n1 n2 Total island capacitance and energy C = CG+C1+C2
65
67
Conductance Variation
68
Effect of temperature
70
1000
100
100
10
10
1 0.1 1
Total island capacitance, CS (aF)
0.1
10
71
capacitance to the junction capacitance Thus for every junction capacitance and temperature, there is a maximum voltage gain.
72
Noises in SET
Johnson noise: -electronic noise generated by the thermal agitation of the charge carriers - usually negligible (thanks to small kT) Shot noise -originates from the discrete nature of electric charge -but is lower in SET. Flicker noise - also known as pink noise. - dominant at low f, may shift the operational point and totally break down the operation Solution : Avoid metal-oxide devices which has a lot of glassy amorphous material surrounding the junctions 73
Advantage of SET
High Speed
Low power dissipation High band width Occupies less space on IC chip
Disadvantage of SET
Noise
Acknowledgements Dr A K V Sir for the guidance Md. Rameez for the eBook References Fundamentals of nanoelectronics by George W. Hanson
THANKS