A. shear strain to compressive strain B. elastic limit to compressive strain C. lateral strain to longitudinal strain D. elastic limit to proportional limit Cold working of steel plates make the metal:
A. harder B. tougher C. more ductile D. more malleable
Manganese steel standard designation, SAE _____
A. 10XX B. 13XX C. 11XX D. 8XXX
The best materials for break drum is:
A. aluminum B. steel material C. wrought iron D. cast iron
Plain carbon steel standard designation, SAE _____
A. 6XXX B. 14XXX C. 4XXX D. 10XX
Molybdenum-chromium- nickel steel designation:
A. SAE 48XX B. SAE 43XX C. SAE 56XX D. SAE 46XX
The rigidity of polymer can be increased by:
A. normalizing B. crystallization C. furnace melting D. shot peening Stresses that are independent of loads is called:
A. working stress B. simple stress C. combined stress D. residual stress Chromium steel standard designation, SAE:
A. 92XX B. 5XXX C. 3XXX D. 11XX Ability to resist deformation under stress:
A. plasticity B. stiffness C. toughness D. all of these A lathe machine threading mechanism:
A. spindle gear B. reverse gear and lever C. change stud gear D. all of these Normal stress relieving temperature for cast steel:
A. 200 to 350 degrees F B. 400 to 500 degrees F C. 300 to 400 degrees F D. 450 to 550 degrees F
The three moment of equation may be used to analyze:
A. tapered column B. composite beam C. continuous beam D. axially and loaded beam The ability of a metal to be deformed considerably without rupture is called:
A. plasticity B. ductility C. malleability D. all of these One of the following materials is not mentioned for wire rope pulley/sheave applications.
A. plastic B. iron C. paper D. copper alloy
In greater quantity, this element is harmful to the molten ferrous metal.
A. silicon B. aluminum C. oxides D. sulfur Some experiments made at Cornell University showed that experience mechanic could break a _____ bolt due to nut tightening.
A. 3/8 inch B. 5/8 inch C. 1/2 inch D. 7/16 inch The arc of action to circular pitch or length of action to base pitch.
A. approach ratio B. contact ratio C. arc of action D. arc of approach Which of the following product of combustion that has a property of resilience?
A. rubber B. grease C. graphite power D. graphite electrode The brittleness in steel at elevated temperature is:
A. hard drawn B. red shortness C. cold lap D. residual stresses Common defects encountered in the foundry shop steel casting operating and also in welding practices.
A. cracks B. cold shot C. parting line D. blow/pin holes The minimum recommended worm pitch diameter is 1/4 in. and the maximum is _____ in.
A. 1 3/4 in B. 2 3/4 in C. 3 in D. 2 in To prevent engine vibration to affect the surrounding area, it is a standard practice to isolate the engine and its foundation by at least _______ mm.
A. 20 B. 30 C. 25 D. 36 The number of protons in the nucleus of an atom of the number of electrons in the orbit of an atom:
A. atomic volume B. atomic number C. atomic weight D. atomic mass
What amount of air is required in a low bypass factor?
A. greater B. indeterminate C. lesser D. does not change What keeps the moisture from passing through the system?
A. trap B. aerator C. dehydrator D. humidifier A theoretical body which when heated to incandescence would emit a continuous light-ray spectrum:
A. black body B. black body radiation C. blue body D. white body Ignition of the air fuel mixture in the intake of the exhaust manifold:
A. backlash B. backfire C. exhaust pressure D. back pressure Heat transfer due to heat differential: ???
A. radiation B. conduction C. convection D. nuclear Is the property of lubricant that will start burning:
A. pour point B. solid point C. fire point D. flash point
In radiation, the heat transfer depends on:
A. temperature B. heat rays C. heat flow cold to hot D. humidity The main cause of air pollution as a result of burning fuel oil is:
A. sulfur dioxide B. hydrogen dioxide C. silicon dioxide D. nitrogen dioxide Number of molecules in a mole of any substance is a constant called:
A. Rankine cycle B. Otto cycle C. Avogadros number D. Thompson constant What is an apparatus used in the analysis of combustible gases?
A. calorimeter differential B. calorimeter gas C. calorimeter D. Calorimetry
A device for measuring the velocity of wind:
A. aneroid barometer B. anemometer C. anemoscope D. anemograph Which is used as a moderator in certain types of nuclear reactors?
A. vapor B. heavy water C. hot water D. cold water What is the force required to accelerate a mass of 1 gram at a rate of 1 cm/sec/sec?
A. dyne B. poundal C. slug D. kg force Foundations are preferably built of concrete in the proportion of what measures of Portland cement: san: crushed stones?
A. 1:2:5 B. 2:4:6 C. 2:3:4 D. 1:2:4 The color of lubricating oil indicates:
A. does not indicated contamination B. does not indicates qualities C. qualities D. viscosity The components of a rotary pump: ???
A. gears B. piston C. impeller D. screw What is the term used in to express the ratio of specific humidities, actual versus saturated?
A. relative humidity B. degree of saturation C. absolute humidity D. percent In a diesel engine, what elements in the fuel that make to work of the lubricant more difficult? ???
A. water and ash content B. high octane number C. high cetane number D. sulphur and asphaltene content Enthalpy of an ideal gas is a function only of:
A. entropy B. internal energy C. temperature D. pressure Crankshaft of reciprocating type compressor is basically made of:
A. semi-steel B. aluminum alloy C. cast iron D. steel forging Which does not belong to the group?
A. air injection system B. mechanical injection system C. time injection system D. gas admission system In a cooling tower, the water is cooled mainly by:
A. condensation B. convection C. evaporation D. conduction Air that controls the rate of combustion in the combustion chamber is known as:
A. secondary air B. excess air C. control air D. primary air What is the color code of air pipelines?
A. light blue B. red C. brown D. violet How many pounds of air are theoretically needed to burn one pound of diesel fuel oil?
A. 28 B. 14 C. 19 D. 22 A major cause of air pollution resulting from the burning of fuel oils is:
A. nitrous B. hydrogen C. sulfur dioxide D. silicon For reciprocating compression slip at positive displacement.
A. cd = 1 B. cd > 1 C. cd < 1 D. cd = 0 For positive slip, the coefficient of discharge:???
A. increases B. decreases C. zero D. constant . __________ is the name applied to reciprocating circular motion as that of a pendulum.
A. intermittent motion B. reciprocating motion C. oscillation D. momentum Not part and in fact should not be used in the steel melting process.
A. silicon B. zinc C. aluminum D. coke Iron based alloy containing 9- 16% chromium.
A. stainless steel B. Mn Hadfield steel C. chrome-alloy steel D. high chrome steel In a cutting tool the cutting end can also be generally called ____.
A. end cutting edge B. back rake C. side rake D. nose An example of rectilinear translation:
A. locomotive wheels B. rack gear C. piston of an engine D. jack All terms and abbreviations deal with wire rope arrangement except this ___ which deals with wire rope material strength.
A. Mps B. preformed C. IWRC D. lang lay A tool not belonging to the group:
A. hermaphrodite caliper B. divider C. double VEE block D. trammel
Silicon manganese steel designation, SAE___.
A. 72xx B. 40xx C. 92xx D. 9xx Permanent deformation or strain may occur without fracture:
A. malleability B. elasticity C. plasticity D. ductility Most effective alloying element for reducing brittleness of steel at very low temperature:
A. manganese B. molybdenum C. nickel D. silicon For a high corrosion resistant stainless steel, what minimum chromium content is required?
A. 4.3% B. 8% C. 1.1% D. 5.8% The phenomenon of continuous stretching under load even if the stress is less than the yield point:
A. creep B. elasticity C. ductility D. plasticity Killed steel is always associated with:
A. manganese B. silicon C. phosphorus D. sulfur Good stabilizer in stainless steel
A. columbium B. titanium C. tantalum D. all of these It is considered semi-solid lubricant:
A. lube oil B. graphite C. grease D. all of these
Moment of inertia is also called:
A. weep strength B. modulus of elasticity C. radius of gyration D. none of these
The recommended lubricant for the chain drive operation.
A. moly slip B. SAE 4140 C. Petroleum oil D. heavy grease
Maximum plant capacity in which a licensed ME is allowed to operate, tend or maintain.
A. 2000 kw B. 1000 kw C. 300 kw D. 3000 kw
Commonly used steel melter as deoxidizer because of its easy availability and cheap price.
A. silicon B. manganese C. aluminum D. zinc
Internal stress exerted by the fibers to resist the action of outside force is called______.
A. tensile stress B. ultimate stress C. compressive stress D. shearing stress
Not part of the headstock.
A. back gear B. spindle C. anvil D. motor
What is the recommended cutting speed range for bronze in fpm?