Académique Documents
Professionnel Documents
Culture Documents
1.0 Introduction
Many researchers have been used FEM for modeling and analysis fixture
workpiece interactions. Commercial finite element solver has also been
employed for FEM calculations. ANSYS software was used to calculate
the displacement of the workpiece at the time of machining.
Year
Objective
Design criteria
Tools used
Menassa
and
DeVries
1991
To determine the
position of supports
FEA
Meyer
and Liou
1997
To synthesize fixtures
for dynamic machining
conditions
Linear
programming
technique
Li and
Melkote
1999
To optimize layout
problem
Minimizes workpiece
location errors due to
localized elastic
deformation of the
workpiece.
Nonlinear
programming
method
Roy and
Liao
1999
Tao et al.
1999
---
Heuristic
method
A geometrical
reasoning
methodology
Year
Objective
Design criteria
Liao and
Hu
2000
Fixtureworkpiece
system subject to timevarying machining loads
Li and
Melkote
2001
---
Contact elasticity
modeling method
Amaral et 2004
al.
Optimization analysis
---
ANSYS
Tan et al.
2004
---
By the methods of
force closure,
optimization and finite
element modeling
Kumar et
al.
1999
Designing a fixture
---
Marcelin
2001
Optimization of support
positions
---
GA
fixture configuration
analysis based on a
dynamic model
Tools used
Influence of clamping
placement is also
investigated
Year
Objective
Design criteria
---
Tools used
Vallapuzha
et al.
2002
Fixture layout
optimization
GA based optimization
method
Krishnakum
ar and
Melkote
2000
Fixture layout
optimization
Minimizes the
deformation of the
machined surface due
to clamping and
machining forces over
the entire tool path
GA
Necmettin
Kaya
2005
To find the
optimal locator
and clamp
positions in 2D
workpiece
GA tool
Year
Objective
Design criteria
---
Tools used
Vallapuzha
et al.
2002
Fixture layout
optimization
GA based optimization
method
Krishnakum
ar and
Melkote
2000
Fixture layout
optimization
Minimizes the
deformation of the
machined surface due
to clamping and
machining forces over
the entire tool path
GA
Necmettin
Kaya
2005
To find the
optimal locator
and clamp
positions in 2D
workpiece
GA tool
REFERENCES
1. Xiumei Kang and QingjinPeng, Recent research on computer-aided
fixture planning, Recent Patents on Mechanical Engineering, Vol. 2,
Pp.8-18, 2009.
2. Nee AYC and Tao ZJ and AS. Kumar, An advanced treatise on fixture
design and planning, World scientific, London, 2004.
3. R.J. Menassa, and W.R. DeVries, Optimization methods applied to
selecting support positions in fixture design, Journal of Engineering for
Industry, ASME Transactions, Vol. 113, Pp. 412418, 1991.
4. S. Jayaram, B.S. El-Khasawneh, D.E. Beutel, and M.E. Merchant, A
fast analytical method to compute optimum stiffness of fixturing locators,
CIRP Annals - Manufacturing Technology, Vol. 49, No.1,Pp.317-320,
2000.
5. Diana M. Pelinescu and Michael Yu Wang, Multi-objective optimal
fixture layout design, Robotics and Computer Integrated Manufacturing,
Vol. 18, Pp.365372, 2002.
REFERENCES
6. Rdrigo A. Marin and Placid M. Ferreira, Analysis of the influence of
fixture locator errors on the compliance of work part features to
geometric tolerance specifications, J. Manuf. Sci. Eng., Vol.
125,No.3, 609 (8 pages),2003.
7. Necmettin Kaya, Machining fixture locating and clamping position
optimization using genetic algorithms, Computers in Industry, Vol. 57,
No.2, Pp.112-120, 2005.
8. ANSYS 8.0, ANSYS Inc., 2003.
9. Wang, X. Chen, Q. Liu, and N. Gindy, Optimisation of machining
fixture layout under multi-constraints, International Journal of Machine
Tools & Manufacture, Vol. 46, Pp.12911300, 2006.
10. Xiaoyun Liao and G. Gary Wang, Simultaneous optimization of
fixture and joint positions for non-rigid sheet metal assembly, The
International Journal of Advanced Manufacturing Technology, Vol. 36(34), Pp.386-394, 2006.
REFERENCES
11. S. Ratchev, K. Phuah, G. Lammel, and W. Huang, An experimental
investigation of fixture workpiece contact behaviour for the dynamic simulation of
complex fixtureworkpiece systems, Journal of Materials Processing Technology,
Vol. 164165, Pp.15971606, 2005.
12. Shao-Gang Liu , Li Zheng , Zhi-Hai Zhang , Zhi-Zhong Li and Da-Cheng Liu,
Optimization of the number and positions of fixture locators in the peripheral
milling of a low-rigidity workpiece, Int J AdvManuf Technol., Vol. 33, Pp.668676,
2007.
13. D. Biermann, , Kersting and T. Surmann, A general approach to simulating
workpiece vibrations during five-axis milling of turbine blades, CIRP Annals Manufacturing Technology, Vol. 59, Pp. 125128, 2010.
14. ShashaZeng , Xiaojin Wan, Wenlong Li , Zhouping Yin and YoulunXiong, A
novel approach to fixture design on suppressing machining vibration of flexible
workpiece, International Journal of Machine Tools & Manufacture, Vol. 58, Pp.29
43, 2012.
15. G. Prabhaharan, K.P. Padmanaban, and R. Krishnakumar, Machining fixture
layout optimization using FEM and evolutionary techniques, Int J
AdvManufTechnol, Vol. 32, Pp. 10901103, 2007.
REFERENCES
16. K.P. Padmanaban, K.P. Arulshri, and G. Prabhakaran, Machining
fixture layout design using ant colony algorithm based continuous
optimization method, Int J AdvManufTechnol, Vol. 33, Pp.668676,
2007.
17. KrishnakumarKulankara, SrinathSatyanarayanaand
Shreyes N.
Melkote, Iterative fixture layout and clamping force optimization using
genetic algorithm, Journal of Manufacturing Science and Engineering,
Vol. 124, pp.119-125, 2002.
18. S. Ratchev, K. Phuah, and S. Liu, FEA-based methodology for the
prediction of partfixture behaviour and its applications, Journal of
Materials Processing Technology, Vol. 191, Pp.260264, 2007.
19. D.C. Mongomery, Design and analysis of experiments, Wiley,
Singapore, 2001.
Any Queries
REFERENCES
Thankyou