Académique Documents
Professionnel Documents
Culture Documents
Terminal Configurations
Windows Environment
system
prompt.
User =
>
Privileged =
CONFIG =
(config)#
POE/POE+
PoE
Device will supply 15.4 watts of power at the RJ-45 jack
PoE+
Device will supply either 15.4 or 30 watts of power
POE/POE+ Configurations
Brocade#configure terminal
Brocade(config)# interface ethernet 1/1
Brocade(config-if-e1000-1/1)# inline power power-limit 14000
commands enable in-line power on interface ethernet 1 in slot 1 and set the PoE power level to
atts (14 watts).
Syntax: inline power power-limit <power level>
<power level> variable is the maximum power level in number of milliwatts. The following values
orted:
PoE: Enter a value from 1000 through 15,400. The default is 15,400.
PoE+: Enter a value from 1000 through 30,000. The default is 30,000.
nn
a
b
For example, to display the message Welcome to FESX! when a Telnet CLI session
no
e
is establishedbanner motd $ (Press Return)
th
ocade(config)#
r
te
n
e
ter TEXT message, End with the character '$'.
r,
e
n
elcome to FESX! $
an
b
he
t
ve
o
em
r
To
etting a privileged EXEC CLI level banner
otd
m
r
You can configure the Brocade device to display a message when a user enters the Privileged
EXEC CLI level.
Example
Brocade(config)# banner exec_mode # (Press Return)
Enter TEXT message, End with the character '#'.
You are entering Privileged EXEC level
up to 4000
Do not foul anything up! #
characters
10
mm
o
c
e
Th
am
n
ca
be
up
to
64
r
a
ch
rs
e
t
ac
n
lo
11
12
e following commands change the port speed of copper interface 8 on a FastIron from the
ault of 10/100/1000 auto-sense, to 100 Mbps operating in full-duplex mode.
Brocade(config)# interface ethernet 8
Brocade(config-if-e1000-8)# speed-duplex 100-full
NOTE
On FastIron devices, when setting the
speed and duplex-mode of an interface
to 1000-full, configure
one side of the link as master (1000full-master) and the other side as slave
(1000-full-slave).
13
t speed down-shift and maximum port speed advertisement work only when
o-negotiation is enabled (CLI command speed-duplex auto). If auto-negotiation is OFF, the
vice will reject the port speed down-shift and maximum port speed advertisement
nfiguration.
14
15
t speed down-shift and auto-negotiation can be configured for an entire range of ports with a
gle command.
example, to configure down-shift on ports 0/1/1 to 0/1/10 and 0/1/15 to 0/1/20 on the
vice, enter the following.
Brocade(config)# link-config gig copper autoneg-control down-shift ethernet 0/1/1 to 0/1/10
ethernet 0/1/15 to 0/1/20
16
17
o configure a maximum port speed advertisement of 10 Mbps on a port that has auto-negotiation
nabled, enter a command such as the following at the Global CONFIG level of the CLI.
Brocade(config)# link-config gig copper autoneg-control 10m ethernet 1
o configure a maximum port speed advertisement of 100 Mbps on a port that has
uto-negotiation enabled, enter the following command at the Global CONFIG level of the CLI.
Brocade(config)# link-config gig copper autoneg-control 100m ethernet 2
Syntax: [no] link-config gig copper autoneg-control 10m | 100m ethernet <port>
[Ethernet [<port>]
18
19
A port can be made inactive (disable) or active (enable) by selecting the appropriate status option.
The default value for a port is enabled.
disable port 8 of a Brocade device, enter the following.
Brocade(config)# interface ethernet 8
Brocade(config-if-e1000-8)# disable
You also can disable or re-enable a virtual
interface. To do so, enter commands such as the
following.
Brocade(config)#interfacevev1
Brocade(configvif1)#disable
20
e globally configured Gbps negotiation mode is the default mode for all Gbps fiber ports. You
n override the globally configured default and set individual ports to the following: NOTE
Gbps negotiation is
not supported on
egotiate-full-auto The port first tries to perform a handshake with the other portICX
to 6430 and ICX
6450 devices.
hange capability information. If the other port does not respond to the handshake attempt,
port uses the manually configured configuration information (or the defaults if an
ministrator has not set the information). This is the default.
uto-Gbps The port tries to perform a handshake with the other port to exchange capability
rmation.
egotiation-off The port does not try to perform a handshake. Instead, the port uses
figuration information manually configured by an administrator.
To change the mode for individual ports, enter commands such as the following.
Brocade(config)# interface ethernet 1 to 4
Brocade(config-mif-1-4)# gig-default auto-gig
Brocade Configuration Examples
21
To determine the flash image version running on a device, enter the show version command at any
evel of the CLI. Some examples are shown below.
22
23
24
x: verify md5 | sha1 | crc32 <ASCII string> | primary | secondary [<hash code>]
25
o generate an MD5 hash value for the secondary image, enter the following command.
o generate a SHA-1 hash value for the secondary image, enter the following command.
rocade#verify sha secondary
rocade#.........................Done
ize = 2044830, SHA1 49d12d26552072337f7f5fcaef4cf4b742a9f525
o generate a CRC32 hash value for the secondary image, enter the following command.
rocade#verify crc32 secondary
rocade#.........................Done
ize = 2044830, CRC32 b31fcbc0
26
27
Software upgrades
28
29
er you make configuration changes to the active system, you can save those changes by writing
m to flash memory. When you write configuration changes to flash memory, you replace the
rtup configuration with the running configuration.
eplace the startup configuration with the running configuration, enter the following command
any Enable or CONFIG command prompt.
Brocade#write memory
30
you want to back out of the changes you have made to the running configuration and return to
e startup configuration, enter the following command at the Privileged EXEC level of the CLI.
Brocade#reload
31
32
E
NOT Make sure you enter each command at the correct CLI level. Since some commands have
identical forms at both the global CONFIG level and individual configuration levels, if the CLI
response to the configuration file results in the CLI entering a configuration level you did not
intend, then you can get unexpected results.
r example, if a trunk group is active on the device, and the configuration file contains a
mmand to disable STP on one of the secondary ports in the trunk group, the CLI rejects the
mmands to enter the interface configuration level for the port and moves on to the next
mmand in the file you are loading. If the next command is a spanning-tree command whose
ntax is valid at the global CONFIG level as well as the interface configuration level, then the
ftware applies the command globally. Here is an example.
33
If the file contains commands that must be entered in a specific order, the commands mus
appear in the file in the required order. For example, if you want to use the file to replace a
E
NOT address on an interface, you must first remove the old address using no in front of the
address command, then add the new address. Otherwise, the CLI displays an error messag
and does not implement the command. Here is an example.
34
35
efault, a Brocade device does not time out serial console sessions. A serial session remains
n indefinitely until you close it. You can however define how many minutes a serial management
on can remain idle before it is timed out.
36
E
NOT
37
E
NOT
38
E
NOT
39
E
NOT
40
E
NOT
41
You can define up to 16 local user accounts on a Brocade device. User accounts regulate who can
access the management functions in the CLI using the following methods:
Telnet access
Web management access
SNMP access
A management privilege level, which can be one of the following:
Super User level (default) Allows complete read-and-write access to the system. This is
generally for system administrators and is the only privilege level that allows you to
configure passwords.
Port Configuration level Allows read-and-write access for specific ports but not for global
parameters.
Read Only level Allows access to the Privileged EXEC mode and User EXEC mode with
read access only.
42
43
en strict password enforcement is enabled on the Brocade device, you must enter a minimum of
ht characters containing the following combinations when you create an enable and a user
sword:
least
least
least
least
two
two
two
two
44
By default, when you use the CLI to create a user password, the password displays on the console
as you type it. For enhanced security, you can configure the Brocade device to mask the password
characters entered at the CLI. When password masking is enabled, the CLI displays asterisks (*) on
the console instead of the actual password characters entered.
The following shows the default CLI behavior when configuring a username and password.
Brocade(config)#username kelly password summertime
The following shows the CLI behavior when configuring a username and password when
password-masking is enabled.
45
46
47
48
49
50
51
52
LAB
Create VLAN
Assign IP to VLAN
MAP Ports to VLAN
VLAN Routing
53
54
THANK YOU!
55