Académique Documents
Professionnel Documents
Culture Documents
QUESTION 1
Which of the following is Rust Grade C?
QUESTION 2
The optimum pressure to achieve 100% efficiency in
abrasive blast cleaning is?
A) 75 psi
B) 450 psi
C) 100 psi
D) 220 psi
BGas PAINTING INSPECTION
QUESTION 3
Sand is not permitted as a dry blast abrasive, as directed
by:
A) BGC/PS/PA10
B) BS 7079 Part A
C) COSHH
D) BS 410
BGas PAINTING INSPECTION
QUESTION 4
How many times can Garnet be used as an abrasive for
BGas site use?
QUESTION 5
The correct ratio of a “working mix” would be:
QUESTION 6
Flame cleaning uses which mechanisms?
QUESTION 7
Carbon Impregnated hoses are used to:
QUESTION 8
One of the most important safety items of equipment in
abrasive blasting is:
QUESTION 9
What is the approximate speed of the abrasive particles
exiting a wheelabrator?
A) 450 mph
B) 220 mph
C) Mach 3
D) 100 psi
BGas PAINTING INSPECTION
QUESTION 10
Where would you normally use a comparator gauge?
QUESTION 11
“Amplitude” refers to what?
QUESTION 12
What is the material used in surface replica tape,
used to measure profile?
A) Mylex
B) Testrex
C) Mylar
D) Mylon
BGas PAINTING INSPECTION
QUESTION 13
How do we remove hygroscopic salts from the substrate:
A) Water blasting
B) Silver nitrate
C) Dry abrasive blast cleaning
D) Chalk or Talc
BGas PAINTING INSPECTION
QUESTION 14
The test for the presence of Hygroscopic Salts, is:
QUESTION 15
How many photographs of flame cleaning standards are
shown in BS 7079 Part A?
A) 4
B) 14
C) 8
D) 16
BGas PAINTING INSPECTION
QUESTION 16
Which abrasive has the effect of stress relieving the
substrate?
A) Copper Slag
B) Metallic Shot
C) Steel Grit
D) Garnet
BGas PAINTING INSPECTION
QUESTION 17
Where would it be advisable to use Steel Grit as an
abrasive?
QUESTION 18
What is the minimum number of readings required for a
Dial Micrometer?
A) Minimum of 10
B) Minimum of 12
C) One only
D) As many as you wish, but the average reading is
recorded
BGas PAINTING INSPECTION
QUESTION 19
Which test would be used to determine for soluble salts in a
marine environment?
A) Potassium Hexacyanoferrate
B) Copper Sulphate
C) Iron Phosphate
D) Silver Nitrate
BGas PAINTING INSPECTION
QUESTION 20
The standard for the test sieves used for the sizing of
abrasives is:
A) BS 7079 Part A
B) BS 410
C) BGC / PS / PA10
D) SI 1657
BGas PAINTING INSPECTION
QUESTION 21
The most common type of abrasive used for BGas site
work is:
A) Copper Slag
B) Grit & Shot mix
C) Garnet
D) Metallic Shot
BGas PAINTING INSPECTION
QUESTION 22
Compared to a Venturi Nozzle, a Straight Bore Nozzle
would give:
QUESTION 23
Anchor Pattern, Key, Peak-to-trough, are names given to
what?
QUESTION 24
What is a “knock out pot”?
A) A drum used for mixing paint and thinners
B) The area on the equipment where static electricity can
build up and be hazardous
C) A vessel for removing oil and moisture from the air
stream
D) A container where any blockages of the nozzle can be
tapped free
BGas PAINTING INSPECTION
QUESTION 25
High Pressure blasting operates up to which pressure?
A) 100 psi
B) 450 psi
C) 30,000 psi
D) 2,250 mph
BGas PAINTING INSPECTION
QUESTION 1
Which of the following is Rust Grade C?
ANSWER: C
BGas PAINTING INSPECTION
QUESTION 2
The optimum pressure to achieve 100% efficiency in
abrasive blast cleaning is?
A) 75 psi
B) 450 psi
C) 100 psi
D) 220 psi
ANSWER: C
BGas PAINTING INSPECTION
QUESTION 3
Sand is not permitted as a dry blast abrasive, as directed
by:
A) BGC/PS/PA10
B) BS 7079 Part A
C) COSHH
D) BS 410
ANSWER: C
BGas PAINTING INSPECTION
QUESTION 4
How many times can Garnet be used as an abrasive for
BGas site use?
ANSWER: C
BGas PAINTING INSPECTION
QUESTION 5
The correct ratio of a “working mix” would be:
ANSWER: C
BGas PAINTING INSPECTION
QUESTION 6
Flame cleaning uses which mechanisms?
ANSWER: C
BGas PAINTING INSPECTION
QUESTION 7
Carbon Impregnated hoses are used to:
ANSWER: D
BGas PAINTING INSPECTION
QUESTION 8
One of the most important safety items of equipment in
abrasive blasting is:
ANSWER: C
BGas PAINTING INSPECTION
QUESTION 9
What is the approximate speed of the abrasive particles
exiting a wheelabrator?
A) 450 mph
B) 220 mph
C) Mach 3
D) 100 psi
ANSWER: B
BGas PAINTING INSPECTION
QUESTION 10
Where would you normally use a comparator gauge?
ANSWER: B
BGas PAINTING INSPECTION
QUESTION 11
“Amplitude” refers to what?
ANSWER: A
BGas PAINTING INSPECTION
QUESTION 12
What is the material used in surface replica tape,
used to measure profile?
A) Mylex
B) Testrex
C) Mylar
D) Mylon
ANSWER: C
BGas PAINTING INSPECTION
QUESTION 13
How do we remove hygroscopic salts from the
substrate:
A) Water blasting
B) Silver nitrate
C) Dry abrasive blast cleaning
D) Chalk or Talc
ANSWER: A
BGas PAINTING INSPECTION
QUESTION 14
The test for the presence of Hygroscopic Salts, is:
ANSWER: A
BGas PAINTING INSPECTION
QUESTION 15
How many photographs of flame cleaning standards are
shown in BS 7079 Part A?
A) 4
B) 14
C) 8
D) 16
ANSWER: A
BGas PAINTING INSPECTION
QUESTION 16
Which abrasive has the effect of stress relieving the
substrate?
A) Copper Slag
B) Metallic Shot
C) Steel Grit
D) Garnet
ANSWER: C
BGas PAINTING INSPECTION
QUESTION 17
Where would it be advisable to use Steel Grit as an
abrasive?
ANSWER: C
BGas PAINTING INSPECTION
QUESTION 18
What is the minimum number of readings required for a
Dial Micrometer?
A) Minimum of 10
B) Minimum of 12
C) One only
D) As many as you wish, but the average reading is
recorded
ANSWER: C
BGas PAINTING INSPECTION
QUESTION 19
Which test would be used to determine for soluble salts in a
marine environment?
A) Potassium Hexacyanoferrate
B) Copper Sulphate
C) Iron Phosphate
D) Silver Nitrate
ANSWER: D
BGas PAINTING INSPECTION
QUESTION 20
The standard for the test sieves used for the sizing of
abrasives is:
A) BS 7079 Part A
B) BS 410
C) BGC / PS / PA10
D) SI 1657
ANSWER: B
BGas PAINTING INSPECTION
QUESTION 21
The most common type of abrasive used for BGas site
work is:
A) Copper Slag
B) Grit & Shot mix
C) Garnet
D) Metallic Shot
ANSWER: A
BGas PAINTING INSPECTION
QUESTION 22
Compared to a Venturi Nozzle, a Straight Bore Nozzle
would give:
ANSWER: D
BGas PAINTING INSPECTION
QUESTION 23
Anchor Pattern, Key, Peak-to-trough, are names given to
what?
ANSWER: B
BGas PAINTING INSPECTION
QUESTION 24
What is a “knock out pot”?
A) A drum used for mixing paint and thinners
B) The area on the equipment where static electricity can
build up and be hazardous
C) A vessel for removing oil and moisture from the air
stream
D) A container where any blockages of the nozzle can be
tapped free
ANSWER: C
BGas PAINTING INSPECTION
QUESTION 25
High Pressure blasting operates up to which pressure?
A) 100 psi
B) 450 psi
C) 30,000 psi
D) 2,250 mph
ANSWER: C