Académique Documents
Professionnel Documents
Culture Documents
TC7WBD125FK
Dual Bus Switch with Level Shift
Note 1: In case that over-shoot noise is detected, this device should be used with clamp diode to prevent the next
stage device from over-stress.
VCC OE2 B1 A2
8 7 6 5
WBD
125
1 2 3 4
OE1 A1 B2 GND
1 2001-12-04
TC7WBD125FK
Truth Table
Inputs
Function
OE
L A port = B port
H Disconnect
System Diagram
A1 B1 A2 B2
OE1 OE2
Maximum Ratings
2 2001-12-04
TC7WBD125FK
Electrical Characteristics
Note 3: Apply the specified current to the switch, then measure the voltages on pins A and B. The on-resistance is
the lower of the two.
Note 4: The propagation delay time is calculated by the RC (on-resistance and load capacitance) time constant.
3 2001-12-04
TC7WBD125FK
AC Test Circuit
Open
Switch 7.0 V Parameter Switch
GND
RL
tpLH, tpHL Open
Output Measure tpLZ, tpZL 7.0 V
CL
RL
RL = 500 W
Figure 1
AC Waveform
tr 2.5 ns tf 2.5 ns
3.0 V
Input 90%
1.5 V
(A, B)
10%
GND
VOH
Output
1.5 V
(B, A)
VOL
tpLH tpHL
tr 2.5 ns tf 2.5 ns
90% 3.0 V
Output Enable
( OE ) 1.5 V
10% GND
tpLZ tpZL
3.5 V
Output (A, B)
Low to Off to Low 1.5 V
VOL +
VOL
tpHZ 0.3 V tpZH
4 2001-12-04
TC7WBD125FK
VOH – VCC Characteristics (typ.)
4.5 4.5
Ta = 85°C Ta = 25°C
(V)
(V)
VOH
VOH
6 mA
3.5 12 mA 3.5 6 mA
12 mA
High-level output voltage
2.5 2.5
2.0 2.0
1.5 1.5
4.50 4.75 5.00 5.25 5.50 5.75 4.50 4.75 5.00 5.25 5.50 5.75
Power supply voltage VCC (V) Power supply voltage VCC (V)
4.5
Ta = 0°C
(V)
4.0
VOH
100 mA
3.5 6 mA
High-level output voltage
12 mA
24 mA
3.0
2.5
2.0
1.5
4.50 4.75 5.00 5.25 5.50 5.75
Figure 4
5 2001-12-04
TC7WBD125FK
Package Dimensions
6 2001-12-04
TC7WBD125FK
· TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of
safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of
such TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc..
· The TOSHIBA products listed in this document are intended for usage in general electronics applications
(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances,
etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires
extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or
bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or
spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,
medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this
document shall be made at the customer’s own risk.
· The products described in this document are subject to the foreign exchange and foreign trade laws.
· The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other
rights of the third parties which may result from its use. No license is granted by implication or otherwise under
any intellectual property or other rights of TOSHIBA CORPORATION or others.
7 2001-12-04