Académique Documents
Professionnel Documents
Culture Documents
Refin Caratteristiche Tecniche Sublime 2022
Refin Caratteristiche Tecniche Sublime 2022
Caratteristiche/Features/Caracteristiques/Eigenschaften/Eigenshappen/Características
Gres Fine Porcellanato – EN 14411 ISO 13006 Gruppo Bla Annex G
Coefficiente di dilatazione termica UNI EN ISO Metodo di prova disponibile/Tests method available/ ≤ 7 10-6•C-1
lineare/Coefficient of thermal 10545/8 Methode d’essai disponible/Verfügbares/Prüfverfahren/
linear expansion/Coefficient de Testmethode beschikbaar/Método de prueba disponible
dilatation thermique linear/Linearer
Wärmeausdehnungskoeffizient/
Lineaire thermische uitzetting/
Coeficiente de dilataciόn termica
linear
Resistenza agli sbalzi termici/ UNI EN ISO Nessun campione deve presentare difetti visibili/ Conforme
Thermal shock resistance/Resistance 10545/9 No sample must show visible defects/ Compliant
aux ecarts de temperature/ Aucun échantillon ne doit présenter des défauts visibles/
Temperaturwechselbeständigkeit/ Kein Exemplar darf sichtbare Schäden aufweisen/
Temperatuurswisselingen/Resistencia Geen enkel monster mag zichtbare gebreken vertonen/
al choque térmico Ninguna muestra debe presentar defectos visibles
Dilatazione all’umidità/Moisture UNI EN ISO Metodo di prova disponibile/Tests method available/ ≤ 0,01 %
expansion/Dilatation à l’humidité/ 10545/10 Methode d’essai disponible/Verfügbares/Prüfverfahren/ (0,1 mm/m)
Feuchtigkeitsausdehnung/Uitzetting Testmethode beschikbaar/Método de prueba disponible
door vocht/Dilatación por la humedad
** Per piastrelle rettangolari, che abbiano il lato maggiore L≥ 60 cm, e rapporto tra i lati ≥ 3, la misurazione della ortogonalità deve venire condotta solo sul lato corto.
For oblong tiles with L≥ 60 cm and ratio length/width L/W≥3, measurement of rectangularity only on short edges
Sublime
Caratteristiche/Features/Caracteristiques/Eigenschaften/Eigenshappen/Características
Gres Fine Porcellanato – EN 14411 ISO 13006 Gruppo Bla Annex G
Resistenza alle macchie/Stain UNI EN ISO UGL Dichiarare un valore / UGL Declare a value Matt/Strutt:
resistance/Insensibilité aux taches/ 10545/14 Classe 5 / Class 5
Beständigkeit gegen Fleckenbildner/
Substanzen/Weerstand tegen vlekken/
Resistencia a las manchas
GL ≥ 3 Lucido:
Conforme
Compliant
Cessione di piombo e cadmio/ UNI EN ISO Valore dichiarato per piastrelle GL / Declared value for GL tiles Lucido:
Lead and cadmium discharge/ 10545/15 Pb < 0,01 mg/dm2
Perte de plomb et cadmium/ Cd < 0,001 mg/dm2
Abgabe von Blei und Cadmium/
Ontdaan van lood en cadmium/
Cesiόn de plomo y cadmio
Indicazione di resistenza allo DIN EN 16165:2021 Dichiarare un valore (R) / Declare a value (R) R10 Matt
scivolamento/Assessment Annex B R11 Strutt./OUT2.0
of slip resistance/Indication
de la résistance au glissement/
Bestimmung der Trittsicherheit/
Indicatie voor de slipvastheid/
Indicación de resistencia al
deslizamiento DIN EN 16165:2021 Dichiarare un valore (A+B+C) / Declare a value (A+B+C) A+B+C OUT2.0
Annex A
Lucido:
Coefficiente di attrito dinamico/ B.C.R.A. Rep. Asciutto > 0,40 / Bagnato > 0,40 Non conforme / Not compliant
Measurement of dynamic coefficient CEC/81 Matt/Strutt/ OUT2.0:
of friction/Mesure du coefficient de Conforme/Compliant
frottement dynamique/Messung des
dynamischen Reibungskoeffizienten/
Meting van de dynamische Matt wet DCOF ≥ 0,50
Test condotto
wrijvingscoefficient/Coeficiente de secondo standard Strutt wet DCOF ≥ 0,42
rozamiento dinámico ANSI A326.3 OUT2.0 wet DCOF ≥ 0,55
(BOT3000)
WARNING: THE POLISHED (LUCIDO) SURFACE DOES NOT MEET THE MINIMUM COEFFICENT OF FRICTION, ACCORDING TO THE MOST RELEVANT NATIONAL STANDARDS FOR ANTISLIP RESISTANCE
(AS PER EXAMPLE: ANSI 137.1-2012 / BOT3000; B.C.R.A. REP. CEC/81; DIN 51130; DIN 51097). THEREFORE WE RECOMMEND TO USE POLISHED (LUCIDO) FINISH FOR WALL APPLICATION ONLY.