Académique Documents
Professionnel Documents
Culture Documents
The relay SW960330 is designed for controlling and inverting the direction of a
three-phase motors without direct third leg ( two legs). Directly mounting on a DIN
rail , this product with a maximum current of semiconductors of 50 Amps. rms ,
can drive a motor with a current rating of 4,5 Amps.rms (or approximately 1,5kW
under 400 V), taking the starting and reversing current into account. These pro-
ducts are designed with very high immunity components , without REED switches
(only composed of solid state components) , with all protections : RC , VDR ,.....
temporisation ,........., and 1600Volt peak voltage components.
100
72
83
25
3x 400VAC
0V
-A2/B2 Forward Reverse
+B1
Control RC -VDR
logic
protection
Reverse +A1
Forward
24-500VAC
12-30VDC
celduc
+ B1 -A2/B2
Solid State
2T1 4T2 6T3
+A1
+ A1
Motor Reverser
F
celduc
M3~
page 2 / 5 F/GB
Forward
Reverse
1L1 Mains
~ or
LED Insu load
lation Switch RC network VDR
6T3 Load
~ or
mains
L3-T3
depending
Insu lation Switch RC network VDR
of models
celduc
r e l a i s
www.celduc.com
page 3 / 5 F/GB
ITSM 550A
(@ 1 cycle of 10ms)
2
I2t value/ Melting limit (choice of fuse) @10ms It 1500 A2s
Courant minimal de charge / Minimum load current Imin 100 mA
facteur de puissance/ Power factor (@ Ie) Pf 0 up to 1
Temps d'ouverture et de temporisation/ Turn on time-reversing time(@50Hz) ton/trv 20ms / 100ms
Temps d'ouverture/ Turn off time (@50Hz) toff 10ms
Courant de fuite /Maximum leakage current (@Ue/50Hz) Ilk 5 mARMS
dv/dt / Max off state voltage rise dv/dt 500V/µs
Fréquence de réseau / Operating frequency range f 25 up to 440Hz
Max conducted immunity level 4KV direct at output, 4KV with a clamp at input
Test accord. to I.E.C.1000-4-4 (bursts) no turn on or damage
Max conducted immunity level 2KV in common mode, 1KV in differential mode (Input & output)
Test acc. to I.E.C.1000-4-5 (el. shocks) no turn on or damage
Max radiated immunity level 10V/m
E.M.C.
celduc
r e l a i s
Rue Ampère B.P. 4 42290 SORBIERS - FRANCE E-Mail : celduc-relais@celduc.com
Fax +33 (0) 4 77 53 85 51 Service Commercial France Tél. : +33 (0) 4 77 53 90 20
Sales Dept.For Europe Tel. : +33 (0) 4 77 53 90 21 Sales Dept. Asia : Tél. +33 (0) 4 77 53 90 19
S/MOT/SW960330/A/16/03/2000
25 25
15 15
10 10
5 5
0 0
0 2 4 6 8 10 12 0 10 20 30 40 50 60 70 80 90 100
RMS load current (A) Ambient temperature (°C)
400
1 : No repetitive Itsm (Apeak)=f(t)
without voltage reapplied
200
2
2 : Repetitive Itsm (Apeak)=f(t) 0
with voltage reapplied for initial Tj
0,01 0,1 t (s) 1 10
=70°C
N.m
0,75 ... 2,5 mm2 0,75 ... 2,5 mm2 0,75 ... 2,5 mm2 0,75 ... 2,5 mm2 0,8 x 5,5 mm POZIDRIV 2 1,2
N.m
1,5 ... 10 mm2 1,5 ... 6 mm2 1,5 ... 10 mm2 1,5 ... 6 mm2 0,8 x 5,5 mm POZIDRIV 2 1,8
celduc
r e l a i s
www.celduc.com
page 5 / 5 F/GB
APPLICATION NOTE :
USING A SW9 RELAY FOR REVERSING AN ASYNCHRONOUS SINGLE
PHASE MOTOR WORKING WITH A PHASE SHIFTING CAPACITOR
ALIMENTATION
MONOPHASE
/ Main voltage
L N
Reverse
Forward
24-500VAC
celduc
12-30VDC
Solid State
+A1
F
Motor Reverser
SW9 2T1 4T2 6T3
Note : The SW9 relay which has been initially developped in order to
reverse three phase asynchronous motors , can be used for reversing
single phase motors . M
This relay has 4 power switches , a reversing temporization and
a lock in case of simultaneous controls . If you need a big quantity for a
single phase use , please contact us , because we are able to simplify the
product as only 2 switches among 4 are used .
celduc
r e l a i s
www.celduc.com