Académique Documents
Professionnel Documents
Culture Documents
FR MODE D’EMPLOI APPROBATIONS ET CERTIFICATIONS (I1 et I2). Il n’est pas possible de combiner un interrupteur basculant
N Entrée Neutre
L Entrée Phase avec un interrupteur poussoir. Pour relancer l’autodétection, il est
Par la présente, NodOn SAS déclare que cet équipement nécessaire de réinitialiser manuellement le module multifonction
radio est conforme à la directive RED 2014/53/UE. Entrée pour
l’interrupteur filaire 1 (I1)* (voir procédure de réinitilalisation du module).
Le texte intégral de la déclaration de conformité Entrée pour
de l’UE est disponible à l’adresse Internet suivante : nodon.fr l’interrupteur filaire 2 (I2)*
section « Support » Borne d’entrée, le potentiel
ON
will pass through the output 3 The relay switch LED will blink green twice,
MULTIFUNCTION The presence of this symbol on a product indicates terminal CONTROL ACCESS MODE confirming the pairing.
that this one is conform to the European directive
RELAY SWITCH 2012/19/UE. Find out more about the provisions in
Output terminal
It is imperative to activate the control access mode Note: if the LED blinks orange during the pairing procedure, it
force in your region regarding the separate collection Each terminal can accept a cable of 2.5mm² maximum, stripped before pairing your remote/wall switch to control your means that more than 22 controllers are paired and that no more
Reference: SIN-2-1-01 of electrical and electronical devices. Respect the local rules and of 8mm. gate/garage door/electric latch to avoid damaging your controller can be paired. You must remove one controller to add
Power supply: 230V AC ~ 50Hz do not throw out the product with common domestic wastes. *Wired switch optional (see the installation diagrams section). equipment. a new one.
Switching capabilities: 230V AC - 10A // 30V DC - 10A The correct rejection of ancient products allows to preserve the Relay switch must be power supplied.
Consumption: <1W environment and health.
Max. Power: 2300W (Resistive load) Figure 3
INSTALLATION - GATE/GARAGE DOOR/ 1 Cut the power supply. USE OF YOUR SOFT BUTTON
List of compatible loads available on nodon.fr/loads ELECTRIC LATCH
Radio frequency range: 868.0 to 868.6 Mhz This product must be used indoor only. 2 Disassemble the cable outlet. The Soft Button will work as follows:
RF power Max: +3dBm 3 Wire the Multifunction Relay Switch following the diagram
Range: up to 30m indoor figure 3, making sure to connect the two wires which controls Types of press Action
Operational temperature: -10°C to 40°C This product is conform to EnOcean radio protocol. the ambient thermostat (see your boiler user guide). Single press Reversal
Protection rating: IP 30 ON
4 Turn the power back ON.
Pairing: up to 22 controllers Double press ON
EEP (EnOcean Profile): D2-01-0F DANGER OF ELECTROCUTION 5 Follow the start-up procedure according to your home
1 Do 5 brief presses on the button of the relay switch. automation gateway. Long press OFF
Dimensions: 40 mm (l) x 44 mm (L) x 16.9 mm (h) BEFORE ANY INSTALLATION MAKE SURE The LED pulses in green, confirming the activation
THE POWER SUPPLY IS DISCONNECTED 6 Reassemble the cable outlet.
Weight: 34 g of the control access mode.
Warranty: 2 years TO AVOID ANY RISK OF ELECTROCUTION.
Directly cut the power supply from the breaker box to avoid 2 You can continue the installation procedure. PAIRING
any risk of electrocution. This relay switch is designed to PAIRING PROCEDURE WITH A HOME AUTOMATION GATEWAY
USE CAUTIONS
be used power up, a wrong installation can create a fire or
• Never use the device if it is not correctly installed and an electric shock. If you are not confident about electrical To add a remote or a wall switch or the Soft Button (EnOcean
compatible) you must enter the pairing mode, your light must For more details on how to pair
placed inside a connecting box in conformity with the installation, please ask a professional. a home automation gateway or
current norms. INSTALLATION - ELECTRICAL OUTLET be switched OFF.
The relay switch must be installed and connected carefully Relay switch must be power supplied. other compatible products, please
• Keep the product far away from liquids. following the instructions of this user guide. We will not be consult the “Support” section on
responsible for any loss or damage resulting from a non- nodon.fr/en/
DETAILED respect of the instructions of this user guide. Cut the power
Figure 1
USER GUIDE supply before any operation and don’t do any modification 1 Cut the power supply.
if the LED is still ON. ON UNPAIRING PROCEDURE
Directly access the detailed user 2 Disassemble the push-button which controls the gate/garage
guide on the Support section door/electric latch.
on nodon.fr/en/technical- Do the same procedure as pairing (see “pairing procedure”) and
support/ INSTALLATION 3 Wire the Multifunction Relay Switch, in parallel to the push- takes care of pressing the button chosen to control your gate/
button following the diagram figure 1. 1 Launch the pairing by doing 3 consecutive presses garage door/electric latch or your electrical outlet.
on the relay switch button.
4 Turn the power back ON. The LED blinks red.
INSTRUCCIONES GEBRAUCHSANWEISUNG Warning: Activate the control access mode (see the
DE USO
section) before pairing to avoid any damage of your
Acceda directa- Gehen Sie direkt zur equipment. RESET PROCEDURE
mente a las ausführlichen Anleitung Figure 2
Thanks to its compact size, the Multifunction Relay Switch 5 Pair the Multifunction Relay Switch, see “Pairing Relay switch must be power supplied.
instrucciones detalladas im Support Bereich unter procedure”.
en la página de soporte de nodon.fr/de/technische- can be installed behind a wall switch, an electrical outlet or 1 Press more than 5 seconds on your module’s button. The
nodon.fr/es/soporte/ unterstuetzung/ a cable outlet. 6 Reassemble the push-button which controls the gate/garage 1 Cut the power supply. LED blinks orange.
door/electric latch. 2 Disassemble the electrical outlet. 2 Press once again the button (short press) to confirm the
3 Wire the Multifunction Relay Switch, following the diagram reset. If the reset is correct, the LED blinks alternatively in red
figure 2. You have now 30 You have now 30
CONTACT AFTER SALES SERVICE TIP seconds to pair your controller seconds to pair your Soft and green and stays green. Start again if necessary.
AUTO-DETECTION OF SWITCH TYPE 4 Turn the power back ON. by briefly pressing on the Button by doing 5 brief 3 Your module has now its original settings.
SIN-2-1-01-UG-V3
NodOn SAS nodon.fr/en/ “support” section Add the Multifunction Relay Switch to the 5 Pair the Multifunction Relay Switch, see “Pairing button of your choice, this one consecutive presses on
121 rue des Hêtres support@nodon.fr electric panel with NodOn DIN Rail Box*. After turning the power supply ON, do a single push on the wired procedure”. will control your gate/garage the button.
45590 St CYR EN VAL wall switch. The relay switch has an auto-detection system to door/electric latch or your
*Optional accessory automatically detect the type of wired wall switch (rocker or 6 Reassemble the electrical outlet
(FRANCE) electrical outlet.
push-button) wired at the input.