Académique Documents
Professionnel Documents
Culture Documents
! Disconnect power to the fan location before installing the fan and light kit!
ENGLISH
! If required by your local electrical code, a licensed electrician must install the fan and light kit.
! Be careful not to damage the LEDs, the electronics on the light module, or the electronics on the bottom of the fan during
installation.
! Contact a licensed electrician if you are uncomfortable performing electrical work or if your local electrical code requires
professional installation!
! Si su código eléctrico local así lo requiere, el ventilador y la luz deben ser instalados por un electricista registrado.
! Al realizar la instalación, tenga cuidado de no dañar los LED, los componentes electrónicos del módulo de luz o los
componentes electrónicos que se encuentran en la parte inferior del ventilador.
! La instalación requiere conocimientos básicos de electricidad. Si no se siente cómodo realizando trabajos eléctricos o si
el código eléctrico local exige una instalación profesional, ¡llame a un electricista registrado!
Before You Start Avant de commencer Antes de comenzar
☑☑ Turn Off Power at Breaker! ☑☑ Coupez l’alimentation électrique ☑☑ Desconecte la alimentación
Contact a licensed electrician if you are Contactez un électricien professionnel si vous ¡Llame a un electricista registrado! Si el código
uncomfortable performing electrical ne vous sentez pas à l’aise avec les travaux local así lo exige, el ventilador debe ser
work. A licensed electrician must install électriques. La règlementation locale peut instalado por un electricista registrado.
the fan if required by local code. exiger que le ventilateur soit installé par un
professionnel. ☑☑ Preparar el lugar de instalación
☑☑ Prepare Fan Site del ventilador
Install Airfoils: Attach the airfoils to the
☑☑ Préparation du site de montage
Asegure las aspas aerodinámicas: Asegure
fan as shown in the fan's installation Montez les pales: Fixez les pales au moyeu du las aspas aerodinámicas al ventilador como se
guide. ventilateur, comme expliqué dans le manuel indica en la guía de instalación del ventilador.
d’installation du ventilateur.
Remove Lower Cover Trim (if fan is Remove Lower Cover Trim (if fan is hanging):
hanging): Remove the lower cover trim Démontez l’enjoliveur du cache inférieur (si le Remove the lower cover trim by carefully
by carefully twisting it counterclockwise. ventilateur est accroché): Démontez l’enjoliveur twisting it counterclockwise.
du cache inférieur en le faisant délicatement
☑☑ Parts and Hardware pivoter dans le sens inverse des aiguilles d’une
☑☑ Piezas y accesorios
• (4) #6 x 1/2" Screws montre.
• (4) #6 x 1/2" Screws
• White Lens and Trim • Lente blanco y borde
• Smokey Lens ☑☑ Composants et visserie • Lente esmerilado
• Light Module • (4) Vis nº 6 x 1/2 po • Módulo de luz
• Lentille blanch + enjoliveur
☑☑ Tools Needed • Lentille fumée†
☑☑ Herramientas necesarias
• Ladder • Module d'éclairage
• Escalera
• Phillips screwdriver
• Destornillador Phillips
☑☑ Outils nécessaires
• Échelle
• Tournevis cruciforme Phillips
Attach the mounting bracket to the fan with four Fixez le support de fixation au ventilateur à Asegure el soporte de montaje al ventilador
(4) #6 x 3/8” screws. Curl the mounting bracket l’aide de quatre (4) vis no 6 × 3/8 po. Plaquez con cuatro (4) tornillos #6 x 3/8 in. Acomode
wires against the inside wall of the bracket to les fils du support de fixation contre la paroi los cables del soporte de montaje contra la
ensure they will not be visible after the light interne du support de telle sorte qu’ils ne soient pared interior del soporte para asegurar que no
module is installed. pas visibles une fois le kit d'éclairage installé. queden visibles después de instalar el módulo
de luz.
SKIP THIS STEP IF INSTALLING A HAIKU SAUTEZ CETTE ÉTAPE SI VOUS INSTALLEZ OMITA ESTE PASO SI ESTÁ INSTALANDO UN
INDOOR FAN WITH SENSEME TECHNOLOGY. UN VENTILATEUR D'INTÉRIEUR HAIKU AVEC VENTILADOR HAIKU PARA INTERIORES CON
LA TECHNOLOGIE SENSEME. TECNOLOGÍA SENSEME.