Académique Documents
Professionnel Documents
Culture Documents
2016)
Free Standard provided by BIS via BSB Edge Private Limited to Government of Telangana -
Hyderabad(rajuanthati25091973@gmail.com) 103.125.163.247 [for non-commercial use only].
(Reaffirmed 2015)
IS 302 ( Part 2/Set 32 ) : 1994
( Reaffirmed 2004 )
(Reaffirmed 2014)
(Reaffirmed 2019)
(Reaffirmed 2013)
(Reaffirmed 2012)
lndian Standard
SAFETY OF HOUSEHOLD AND (Reaffirmed 2011)
SIMILAR
ELECTRICAL APPLIANCES
PART 2 PARTICULAR REQUIREMENTS
(Reaffirmed 2009)
UDC 615’825’9 : 614’825
(Reaffirmed 2008)
(Reaffirmed 2007)
(Reaffirmed 2006)
(Reaffirmed 2005)
0 BIS 1994
FOREWORD
This Indian Standard was adopted by the Bureau of Indian Standards, after the draft finalized by
the Electrical Appliances Sectional Committee had been approved by the Electrotechnical Division
Council.
This standard covers general and safety requirements of electrical appliances intended for massage
purposes. This standard does not cover performance requirements which is covered under a separate
composite standard IS 7137 : 1973.
This standard is to be read in conjunction with IS 302-I ( 1979 ). For the sake of convenience, the
clauses of this standard correspond to those of IS 302-l ( 1979 ). Instead of reproducing full text
of each clause, clauses of IS 302-l ( 1979 ) which are applicable ( which means that relevant
provisions of the clause apply ) or not applicable and the sub-clauses or portions thereof which are
not applicable are indicated as under:
a) In case of a clause where it is applicable or not applicable, the wording used is ‘This clause
of IS 302-I ( 1979 ) is applicable/not applicable’.
Any addition to the existing provisions of a sub-clause of IS 302-l ( 1979 ) has been indicated as
under:
‘Addition-followed by the text of the additional matter’.
Clauses/tables which are additional to those of IS 302-l ( 1979 ) are numbered starting from 101
and additional sub-clauses are numbered with the main clause number followed by 101, 102 etc,
for example, 4.10 1.
Should however any deviation exist between IS 302-l ( 1979 ) and this standard, the provisions of
the latter shall apply.
While preparing this standard, assistance has been derived from the following publications issued
by the International Electrotechnical Commission:
IEC Pub 335-l ( 1976 ) Safety of household and similar electrical appliances: Part 1 General
requirement.
IEC Pub 335-2-32 ( 1987 ) Safety of household and similar electrical appliances: Part 2
Particular requirements for massage appliances.
The Indian Standards listed in Annex AA are necessary adjunct to this standard.
For the purpose of deciding whether a particular requirement of this standard is complied with,
the final value, observed or calculated. expressing the result of a test, shall be rounded off in
accordance with IS 2 : 1960 ‘Rules for rounding off numerical values ( revised I’. The number of
significant places retained in the rounded off value should be the same as that of the specified value
in this standard.
Free Standard provided by BIS via BSB Edge Private Limited to Government of Telangana -
Hyderabad(rajuanthati25091973@gmail.com) 103.125.163.247 [for non-commercial use only].
Indian Standard
SAFETYOFHOUSEHOLDANDSIMILAR
ELECTRICALAPPLIANCES
PART 2 PARTICULAR REQUIREMENTS
Appliances intended primarily for purposes other than 2.101 Electric Massager - A hand held, portable
massage, but which have accessories for massage electrical appliances for simulating the muscles of the
purposes are within the scope of the standard covering human body. It includes cables and connectors.
the primary function.
3 GENERAL I~EQI.TIRI~MENT
This standard dots not take into account the special
halards which exist in nurseries and other places
This clause of IS 302-l(1979) is applicable.
where there are young children or aged or infirm
persons without supervision; in such cases additional 4 GENERAI, NOTES ON TICS’J’S
requirements may br necessary.
This claose of IS 302-l(1979) is applicable except as
2 TERMINOLOGY follow :
This clause of IS 302-l(1979) is applicable except as AdcIitional Sub-clause :
follows :
4.101 Massage appliance are tested as portable
2.30 Replacement appliances, unless they are designed to bc fixed to a
Normal load denotes the load obtained when the support in normal use.
appliance is operated under the following conditions. Hand-held appliances are subjected to the additional
Hand held massage appliances are operated with no tests specified for such appliances.
external load othrr than that imposed by the vibrator
head. 5 RATING
Massage appliances intended to be used under the This clause of IS 302-l(1979) is applicable.
foot or feet of a sitting person are operated with the
platform loaded with a mass of 5 kgevenly distributed 6 CLASSIFICATION
over an area of 10 fm x 30 cm.
This clause of IS 302-l(1979) is applicable.
Massage appliances intended to be used under the feet
of a standing person are operated with the platform 7 MARKING
load with a mass of SO kg evenly distributed over an
arcn of 10 cm x 30 cm. This clause of IS 302-l(1979) is applicable.
Massage belts are operated with the belt loaded by Additional Sub-clause :
means of a roller with a force of 200 N applied in a
hori~ontnl direction so Ihat the belt is approximately 7.101 The massage appliances may also be marked
symmetrical about the roller. with the st;lndard mark.
Massage pads intrndcd to bc used under a sitting 7.102 The use of the standard mark is governed by
person are opcratcd with the pad placed bctwcen two the provisions of Bureau of Indian Standards Act,
1
Free Standard provided by BIS via BSB Edge Private Limited to Government of Telangana -
Hyderabad(rajuanthati25091973@gmail.com) 103.125.163.247 [for non-commercial use only].
1986 and the rules and rcgulatious made thereunder. 17 OVERI,OAD I’ROTECTION
The details of conditions under which the licrnce for
the use of the standard mark may bc granted to This clause of IS 302-l(1979) is applicable.
manufacturers or producers may be obtained from the
Bureau of Iudian Standards. 18 ENDI TRANCE (1Jnder Consideration).
This clause of IS 302-l(1979) is applicable. Conipliaucc is checked by the tests of the following
sub-clauses :
11 TEMPERATURE-RISE - for Class II ulassagc appliances with heating
This clause of IS 302-l(1979) is applicable except as elemeuts aud for massage beds with heating
t’ollows : clcments, if these appliances arc provided
with a control which Iimils the temperature
11.2 Addition during the test of Clause ll.......Sub-clause
Massage appliances incorporating heating elements 19.4.
are also positioned as specified for motel-operated - for hand-held massage appliances with heating
appliances. elcn~cnts other than appliances which have to
11.7 Replacement be kept switched on by hand.......... Sub-clause
19.5.
Hand-held massa~c appliauccs are operated for 20
min. Olhrr niassagc appliauccs i1P.T operated - for IllilSSilgC ilppliilllCCS illcotpriltillg motors
conliuuously unlil steady conditions arc established. having a locked rotor torque snulller than the
full load torque for those having a capacitor
11.8 Addition not complying with IS 2993 : 1975 ilC motor
capacitors, in the circuil ol’au auxiliarv winding
The tempcraturc rise of parts which in normal USC’arc
and Ihr njassage beds . .. . .. . .._ Suh-cli;usc 19.6.
in contact with skin or hair or arc held in the hand
shall not exceed the limits spccifird for handles which - for n~assagc~ beds, other ~II;III 111ose incorpora-
in noma use are continuously held. The tcmpcraturc ting ~~lag~~ctic;rlly-dri\~c~ll\,ibralors . .. ...... . Sub-
rise of such parts is dctcrmincd for every ac’ccssory CIilUSe 19.8.
intcndcd to bc used with the appliance.
- for 1llilSS;lgC appl iilnccs incorpOr;lting series
For Illassagc pads with hcatiug ele~uc~~isIhe tcm~raturl: motors . . . .. . . .. . Sub-clause 19.10.
limits spccificd for hcatiug pads in the relevant Indiau
Standard for hcatiug pads shall apply. 19.4 RepIncement
12 OPEH.4’I’ION IJNDER OVERl,OA1) The appliauce is opcratcd under noma load, ally
CONDITIONS 01; Al’l’i , :ANCl;S >. \VITH Ihcrnlal conlrol which limits Ihe ~cmpcralure during
HkXTIN<; I’IXMKNTS the lest of Clause 11 being short-circuited. Nealiug
elcnltnts arc operated at a supply \~ollag~ such lhal
This clause ot’ IS 302-l(1979) is applic*ablc. ?‘1 linics Ihcir maxinnIn1
llic iiipul to Ilirsc clcnlcnt% is 1.A
rated input, and 111~motor is operated ;II it v(jllagc
13 EI.I’C’l’RI<:r’.l. INSlJIATlON .4ND 1,1’,4KA(;li equal to 1.06 times the rated \r(j11;Igc of the ap]>liaucc.
(:l IRRENT AT OI’I’RATlNG miv mx.4w IRE
It the appliallce is provided \vilh more thanone conlrol
This clause of IS 302-1(1’)79) is al~plicablc. Ihcse arc short-circuited in turii.
14 R.41110 AND ‘I’I~I.I~~VISION IN’I’I:,I~l~I~:III’N~~~~:
1, ,
SIJI’I’Rl’SSlON
This clause of IS 302-l (1079) is applicable. The ~csl of Sub-cl;~usc 19.4 is rcpoated but with the
thrrnlal control not shorl-circuited. The tcsl is coulinucd
15 I\IOISTIiRI’ Rl’SISTAN(‘E unlil slcady coudiIions arc cslablixllcd irrc>pcctivc 01‘
lhr rated opcratiug time.
This clause of IS 302- 1(1079) is applicable.
Alternative tests for protcctcd motor units arc given Instead of the tcXt of a) the following applies :
in Amlex I?. - Swilchcs in ilcxiblc cables or cords, cxccpt
for InaSS;lgc pds :
19.10 Addition
DcIachable parts \vhich may iuflucncc the load arc 24.9 Replacement
removed. h/lassagc pads shall bc fitted with a switch in their
supply circuil.
20 S’I’hl~lI,I’I’Y ANI) RII’<:HAN1(:AI.H,4~~KI)S
25 SIJI’I’LY C:ONNIS(:‘I-ION ANI) EX’I-ERNAI,
This ClilUSC 01’ IS 302-l(1979) is al~l~IicabIc CXCCpl :lS I~I,F:XIBI,E C’AI11,b:S ANI) CORDS
folIows :
This clause of IS 303_-l(1979) is applicable CXCC~~ :IS
21.1 Addition il slmll t)c WI less Ihn 2.05 111 if supplied without
plug.
The 1ho1 I~laIl’orln 01‘Itl;I\sitgc appliallccs intended (0 Type Z atIac]lIlIeIII is aIlo\vcd.
hc used uudcr Ihc fool of a sitting person is then
ImdcJ for 30 s with ;I nwss of’80 kg cvcnly dislribulcd 26 ‘lI’RRIINAI,S FOR k;XTERN.41,
o\‘cr ill1 ilTCil Of’ 10 Cl11 X 30 (‘111. (:ONL)IJC’I’ORS
3
Free Standard provided by BIS via BSB Edge Private Limited to Government of Telangana -
Hyderabad(rajuanthati25091973@gmail.com) 103.125.163.247 [for non-commercial use only].
x) Overload protection
This clause of IS 3(X2-1(1979) is applicahlc. xi) Endurance (under cnnsidcration)
xii) Abnormal operation
xiii) Stability and mechanical hamrds
xiv) Mcchnnical strrngtb
This Clause of IS 302-l(1979) is applicable except as
XV) <‘onslruction
follows : xvi) Intcmd \viring
xvii) Components
31.1 Replacement xviii) Supply connections and cstarnal
flcxihle cables and cord<
The ferrous pad, the rusting of which might cause the xis) Trrminals for external conductors
appliance to fail to comply with this standard, shall xx) Provision for carthing
hc iIdCqUately protected against rusting. xxi) Screws and connections
xxii) Crccpagr dist:rnce and clearances
101.1 Type Tests The following shall c.otIslilutc the acceplancc tests :
The tests specified in Table 101 shall constitute the SI No. ‘fe’41 Clause
lypc tests and shall bc carried oul on two samples of Reference
INISSilgC appliilllccs Of IllC?Silllle lypc’ illld rating SClCCtCYJ
preferably at random from a regular production 101. a) f’rotcction again\t clcclric shock 8
Before C’ollllllellcclnenl of the tests, the massilge
1,) 1“]“I t 10
;lppliallces shall be visually examined and inspcctctl
for obvious visual defects in respect of components, c) Tcnlperature rise 11
1’;)rts aIld their assembly, cooslndion, mechanical
hazards, markings, provision of suitable terminals for d) Electrical illsulaIiol1 and leakage 13
supply conncclions, carlliing and the cffcctivcncss of current at operating temperature
screws and connections. The exterllal surface finish c) Moisture resistance 15
shall be even and free from finishing defecls.
f) Insulation resistance and clcctrir 16
101.1 .l Crilericr ji)r Acupt~tiw strenglh (aflrr humidity Ircalmeiit)
Both s;~~~I~Ics~1~11 SUCCCSS~U~~Y IXISS iIt1 the type (CStS g) Provision for eilrlhillg 27
for proving conformity with thr requirements of the NO’IX- 1.w the purpose of nccelmnc~ tests. the humidity
slandard. If any of the SilIll~?lCS fililS in any Of the type trcatnwnt <hall he done for 21 hour< while conducting the test
tests, the testing authority, at its discretion, may call for nmihturc rcsistancc (15).
ANNEX A
ANNEX B
(Clarrse
1012.1
)
SAMI’LING 1’ROCEDIJRE FOR ACCEPTANCE ‘rESTS
ANNEX C
ELECTRONIC CIRCIJITS
ANNEX D
MEASUREMENT OF TEMPERATTJRE WITH T~IERhZOhll~~rERS
ANNEX E
AI~TERNATIVE TESTS FOR PROTECTISI) MOTOR UNITS
ANNEX F
IMPACT TEST APPARATUS
ANNEX G
5
Free Standard provided by BIS via BSB Edge Private Limited to Government of Telangana -
Hyderabad(rajuanthati25091973@gmail.com) 103.125.163.247 [for non-commercial use only].
ANNEX H
ANNEX J
TEST I’OR FIRI’: RI~SISTIN<; I’ROl’ERTII~S
ANNEX K
BNF .1b:‘I’ TI~:ST IWR 1)IS’I’ERMINATION 01’ THICKNESS OF COPPER AND
NICKEL I’LATING
ANNEX I,
APl’I~OXIMATI~ XII’.4SURISMENT OF THICKNESS 01: <‘HI~OhlIllhl ON NICKb:I,, SI‘EEI,
AND COI’I’FR1
ANNEX AA
IS No. Title IS No. Title
6
Free Standard provided by BIS via BSB Edge Private Limited to Government of Telangana -
Hyderabad(rajuanthati25091973@gmail.com) 103.125.163.247 [for non-commercial use only].
RIS is a statutory institution established under the Burcou of Indian Stundurds Act, 1986 to promote
harmonious development of the activities of standardization, marking and quality certification of goods
and attending to connected matters in the country.
Copyright
BIS has the copyright of all its publications. No part of these publications may be reproduced in
any form without the prior permission in writing of BIS. This does not preclude the free use, in the
course of implementing the standard, of necessary details. such as symbols and sizes, type or grade
designations. Enquiries relating to copyright be addressed to the Director ( Publications ), BIS.
Indian Standards are reviewed periodically and revised, when necessary and amendments, if any, are
issued from time to time. Users of Indian Standards should ascertain that they are in possession of
the latest amendments or edition.
This Indian Standard has been developed from Dot : No. ETD 32 ( 3692 )
Headquarters: