Académique Documents
Professionnel Documents
Culture Documents
No Tag No. Q'ty Size Rating P&ID No Tag No. Q'ty Size Rating P&ID
1 PV-1102B / 1202B 2 4" ASME 1500# SNO-R-PI-005 / 040 66 PV-8067B 1 4" ASME 300# SNO-R-PI-131
2 PV-1102F / 1202F 2 20" ASME 900# SNO-R-PI-005 / 040 67 PV-8067C 1 4" ASME 300# SNO-R-PI-131
3 LV-1102F / 1202F 2 4" ASME 900# SNO-R-PI-005 / 040 68 LV-8067C 1 2" ASME 150# SNO-R-PI-131
4 LV-1104C / ILV-1204C 2 3" ASME 1500# SNO-R-PI-006 / 041 69 LV-6075C 1 2" ASME 1500# SNO-R-PI-150
5 LV-1104F / 1204F 2 3" ASME 1500# SNO-R-PI-006 / 041 70 LV-6071F 1 3" ASME 1500# SNO-R-PI-150
6 PV-1104F / 1204F 2 10" ASME 900# SNO-R-PI-006 / 041 71 PV-6073A 1 4" ASME 600# SNO-R-PI-152
7 LV-1105C / 1205C 2 2" ASME 1500# SNO-R-PI-007 / 042 72 PV 6073B 1 4" ASME 600# SNO-R-PI-152
8 LV-1105E / 1205E 2 2" ASME 1500# SNO-R-PI-007 / 042 73 PV 6075E 1 4" ASME 600# SNO-R-PI-152
9 LV-1105I / 1205I 2 2" ASME 1500# SNO-R-PI-007 / 042 74 FV-2102B / 2202B 2 12" ASME 600# SNO-R-PI-301 / 311
10 LV-1105K / 1205K 2 2" ASME 1500# SNO-R-PI-007 / 042 75 LV-2102B / 2202B 2 12" ASME 900# SNO-R-PI-301 / 311
11 PV-6101E1 / 6201E1 2 2" ASME 150# SNO-R-PI-008 / 043 76 PV-2102B / 2202B 2 6" ASME 600# SNO-R-PI-301 / 311
12 PV-6101E2 / 6201E2 2 3" ASME 150# SNO-R-PI-008 / 043 77 PV-2104G / 2204G 2 2" ASME 150# SNO-R-PI-302 / 312
13 LV-6101B / 6201B 2 2" ASME 150# SNO-R-PI-008 / 043 78 PV-2104H / 2204H 2 2" ASME 150# SNO-R-PI-302 / 312
14 FV-6071A3 1 2" ASME 150# SNO-R-PI-010B 79 LV-2104E / 2204E 2 12" ASME 150# SNO-R-PI-302 / 312
15 FV-6072A 1 16" ASME 150# SNO-R-PI-010C 80 TV-2109 / 2209 2 12" ASME 150# SNO-R-PI-303 / 313
16 FV-6112 / 6212 2 4" ASME 150# SNO-R-PI-012 / 047 81 FV-2106A / 2206A 2 12" ASME 300# SNO-R-PI-304 / 314
17 FV-6105A / 6205A 2 6" ASME 300# SNO-R-PI-013 / 048 82 FV-2106B / 2206B 2 12" ASME 300# SNO-R-PI-304 / 314
18 LV-6103E / 6203E 2 2" ASME 600# SNO-R-PI-013 / 048 83 PV-2105D / 2205D 2 6" ASME 150# SNO-R-PI-305 / 315
19 PV-6107B / 6207B 2 3" ASME 150# SNO-R-PI-014 / 049 84 FV-2114 / 2214 2 3" ASME 150# SNO-R-PI-305 / 315
20 PV-6107C / 6207C 2 4" ASME 150# SNO-R-PI-014 / 049 85 LV-2123H / 2223H 2 2" ASME 600# SNO-R-PI-306 / 316
21 FV-6107B / 6207B 2 2" ASME 300# SNO-R-PI-014 / 049 86 FV-2110 / 2210 2 6" ASME 600# SNO-R-PI-307 / 317
22 FV-6107C / 6207C 2 2" ASME 300# SNO-R-PI-014 / 049 87 FV-2112 / 2212 2 6" ASME 150# SNO-R-PI-309 / 319
23 ILV-6107F / 6207F 2 2" ASME 150# SNO-R-PI-014 / 049 88 LV-2103A / 2203A 2 12" ASME 150# SNO-R-PI-309
24 LV-6040C1 1 2" ASME 150# SNO-R-PI-015 89 LV-3102B / 3202B 2 2" ASME 600# SNO-R-PI-401 / 411
25 LV-6040C2 1 2" ASME 150# SNO-R-PI-015 90 LV-3102E / 3202E 2 2" ASME 600# SNO-R-PI-401 / 411
26 LV 6040E1 1 2" ASME 150# SNO-R-PI-015 91 PV-3116M / 3216M 2 6" ASME 600# SNO-R-PI-402A / 412A
27 LV 6040E2 1 2" ASME 150# SNO-R-PI-015 92 LV-3116B1 / 3216B1 2 2" ASME 600# SNO-R-PI-402A / 412A
28 PV-5102B / 5202B 2 8" ASME 600# SNO-R-PI-017 / 071 93 LV-3116E1 / 3216E1 2 2" ASME 600# SNO-R-PI-402A / 412A
29 LV-5103B / 5203B 2 6" ASME 300# SNO-R-PI-018 / 072 94 PV-3116L / 3216L 2 2" ASME 600# SNO-R-PI-402A / 412A
30 LV-5104B / 5204B 2 2" ASME 1500# SNO-R-PI-018 / 072 95 LV-3116B2 / 3216B2 2 2" ASME 600# SNO-R-PI-402B / 412B
31 LV-6103C / 6203C 2 4" ASME 300# SNO-R-PI-019 / 054 96 LV-3116E2 / 3216E2 2 2" ASME 600# SNO-R-PI-402B / 412B
32 FV-6003A 1 6" ASME 150# SNO-R-PI-022 97 PV-3020B1 1 6" ASME 150# SNO-R-PI-403
33 FV-6004A 1 6" ASME 150# SNO-R-PI-022 98 PV-3020B2 1 6" ASME 150# SNO-R-PI-403
34 FV-6004B 1 8" ASME 150# SNO-R-PI-022 99 TV-3020A1 1 2" ASME 600# SNO-R-PI-403
35 LV-1102C / 1202C 2 4" ASME 1500# SNO-R-PI-029 / 056 100 TV-3020A2 1 2" ASME 600# SNOR-PI-413
36 PV-7101B / 7201B 2 3" ASME 1500# SNO-R-PI-029 / 056 101 FV-3104A / 3204A 2 6" ASME 300# SNO-R-PI-403 / 413
37 FV-7004B4 1 2" ASME 150# SNO-R-PI-032B 102 FV-3104C / 3204C 2 2" ASME 600# SNO-R-PI-403 / 413
38 FV-7004A4 1 2" ASME 150# SNO-R-PI-032B 103 LV 3110B / 3210B 2 3" ASME 150# SNO-R-PI-406 / 416
39 PV-5010G1 / PV5010G2 2 20" ASME 600# SNO-R-PI-033 104 PV-6051 1 3" ASME 150# SNO-R-PI-602
40 FV-6012A 1 6" ASME 150# SNO-R-PI-035 105 FV-6102B 1 4" ASME 150# SNO-R-PI-602
41 FV-6013A 1 6" ASME 150# SNO-R-PI-035 106 LV-6102B 1 6" ASME 150# SNO-R-PI-602
42 FV-6014A 1 6" ASME 150# SNO-R-PI-035 107 TV-6109 1 4" ASME 150# SNO-R-PI-603
43 FV-6020A 1 20" ASME 150# SNO-R-PI-036 108 FV-6106 1 6" ASME 300# SNO-R-PI-604
44 PV-4001A 1 2" ASME 150# SNO-R-PI-038 109 PV-6105D 1 6" ASME 150# SNO-R-PI-605
45 FV-6007 1 3" ASME 150# SNO-R-PI-059 110 FV-6114 1 2" ASME 150# SNO-R-PI-605
46 FV-6007B 1 2" ASME 600# SNO-R-PI-059 111 LV-6123H 1 2" ASME 150# SNO-R-PI-606
47 FV-6008B 1 2" ASME 600# SNO-R-PI-059 112 FV-6112 1 3" ASME 150# SNO-R-PI-607
48 PV-5011G1 / 5011G2 2 18" ASME 600# SNO-R-PI-070 113 LV-6103A 1 4" ASME 150# SNO-R-PI-607
49 PV-8065A 1 6" ASME 600# SNO-R-PI-101 114
50 PV-8065B 1 6" ASME 600# SNO-R-PI-101 115
51 PV-8065C 1 6" ASME 600# SNO-R-PI-101 116
52 LV-8065C 1 2" ASME 300# SNO-R-PI-101 117
53 PV-8066A 1 2" ASME 300# SNO-R-PI-102 118
54 FV-8043A 1 12" ASME 300# SNO-R-PI-104 119
55 FV-8143A / 8243A 2 12" ASME 300# SNO-R-PI-104 120
56 FV-8145E 1 6" ASME 300# SNO-R-PI-106 121
57 FV-8245E 1 6" ASME 300# SNO-R-PI-106 122
58 TV-8145H / 8245H 2 14" ASME 300# SNO-R-PI-106 123
59 FV-8074B 1 3" ASME 150# SNO-R-PI-110 124
60 FV-9050A 1 2" ASME 150# SNO-R-PI-113 125
61 FV-8092A 1 2" ASME 150# SNO-R-PI-113 126
62 FV-9054A 1 2" ASME 150# SNO-R-PI-114 127
63 FV-9054C 1 2" ASME 600# SNO-R-PI-114 128
64 FV 9032B 1 2" ASME 150# SNO-R-PI-117B 129
65 PV-8067A 1 4" ASME 300# SNO-R-PI-131 130
33 End Connections & Rating RTJ Flanged ASME B16.5 1500# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RTJ Flanged ASME B16.5 900# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A351 CF8M , NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RTJ Flanged ASME B16.5 900# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A351 CF8M, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RTJ Flanged ASME B16.5 1500# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RTJ Flanged ASME B16.5 1500# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RTJ Flanged ASME B16.5 900# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A351 CF8M, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RTJ Flanged ASME B16.5 1500# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
10. Assume flowrate is taken from 5 minutes drain from HLL to LLL (Max Case), 10 minutes for HLL to LLL (Nor Case).
33 End Connections & Rating RTJ Flanged ASME B16.5 1500# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
10. Assume flowrate is taken from 5 minutes drain from HLL to LLL (Max Case), 10 minutes for HLL to LLL (Nor Case).
33 End Connections & Rating RTJ Flanged ASME B16.5 1500# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
10 Assume flowrate is taken from 5 minutes drain from HLL to LLL (Max Case), 10 minutes for HLL to LLL (Nor Case).
33 End Connections & Rating RTJ Flanged ASME B16.5 1500# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
10. Assume flowrate is taken from 5 minutes drain from HLL to LLL (Max Case), 10 minutes for HLL to LLL (Nor Case).
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 114.9
19 Vapour Pressure of Liquid @ T1 psig 0.064
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 26.9
23 Inlet Pressure P1 psig 87.9
24 Specific Heat Ratio ( Cp/Cv) 1.017
25 Outlet Pressure P2 psig 57.5
26 Effective Pressure Drop DP psi 30.4
27 Calculated Cv - VTA VTA
28 % Opening VTA VTA
29 Predicted SPL dBa VTA VTA
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 2 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A351 CF8M, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Standard 62 Accessories Gauge
37 Flow Direction Horizontal 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 114.9 114.9 114.9
19 Vapour Pressure of Liquid @ T1 psig 0.064 0.064 0.064
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 26.9 26.9 26.9
23 Inlet Pressure P1 psig 67.5 68 84
24 Specific Heat Ratio ( Cp/Cv) 1.017 1.017 1.017
25 Outlet Pressure P2 psig 57.5 55.3 44.5
26 Effective Pressure Drop DP psi 10 12.7 39.5
27 Calculated Cv - VTA VTA
28 % Opening VTA VTA
29 Predicted SPL dBa VTA VTA
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 8 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A351 CF8M, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A351 CF8M, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 300# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A105N 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
10. Assume flowrate is taken from 5 minutes drain from HLL to LLL (Max Case), 10 minutes for HLL to LLL (Nor Case).
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A351 CF8M, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A351 CF8M, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 300# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 300# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
10. Pump minimum flow is designed based on 30% of pump flow
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 68.9
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.6
23 Inlet Pressure P1 psig 116.4
24 Specific Heat Ratio ( Cp/Cv) 1.4
25 Outlet Pressure P2 psig 4.5
26 Effective Pressure Drop DP psi 111.9
27 Calculated Cv - VTA VTA
28 % Opening VTA VTA
29 Predicted SPL dBa VTA VTA
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 1 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 68.9
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.6
23 Inlet Pressure P1 psig 116.4
24 Specific Heat Ratio ( Cp/Cv) 1.4
25 Outlet Pressure P2 psig 4.5
26 Effective Pressure Drop DP psi 111.9
27 Calculated Cv - VTA VTA
28 % Opening VTA VTA
29 Predicted SPL dBa VTA VTA
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 1 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 68.9
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.6
23 Inlet Pressure P1 psig 116.4
24 Specific Heat Ratio ( Cp/Cv) 1.4
25 Outlet Pressure P2 psig 4.5
26 Effective Pressure Drop DP psi 111.9
27 Calculated Cv - VTA VTA
28 % Opening VTA VTA
29 Predicted SPL dBa VTA VTA
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 1 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 68.9
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.6
23 Inlet Pressure P1 psig 116.4
24 Specific Heat Ratio ( Cp/Cv) 1.4
25 Outlet Pressure P2 psig 4.5
26 Effective Pressure Drop DP psi 111.9
27 Calculated Cv - VTA VTA
28 % Opening VTA VTA
29 Predicted SPL dBa VTA VTA
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 1 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F 99 99 99
18 Density r1 @ T1 lb/ft3 3.065 3.066 3.072
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig 654.4 654.4 654.4
21 Critical Temp of Vapor (flashing) °F -93.22 -93.22 -93.22
22 Viscosity @ T1 cP 0.013 0.013 0.013
23 Inlet Pressure P1 psig 846.6 849 859.3
24 Specific Heat Ratio ( Cp/Cv) 1.48 1.48 1.48
25 Outlet Pressure P2 psig 79.6 72.7 54.4
26 Effective Pressure Drop DP psi 767 776.3 804.9
27 Calculated Cv - VTA VTA
28 % Opening VTA VTA
29 Predicted SPL dBa VTA VTA
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 4 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 300# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A351 CF8M, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F 60 60 60
18 Density r1 @ T1 lb/ft3 5.48 5.54 6.84
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig 515.7 515.7 515.7
21 Critical Temp of Vapor (flashing) °F 258.3 258.3 258.3
22 Viscosity @ T1 cP Mixed Mixed Mixed
23 Inlet Pressure P1 psig 840 841.4 844.6
24 Specific Heat Ratio ( Cp/Cv) 1.06 1.06 1.06
25 Outlet Pressure P2 psig 195.4 195.5 158.5
26 Effective Pressure Drop DP psi 644.6 645.9 686.1
27 Calculated Cv - VTA VTA
28 % Opening VTA VTA
29 Predicted SPL dBa VTA VTA
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 1" inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RTJ Flanged ASME B16.5 1500# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 300# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RTJ Flanged ASME B16.5 1500# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3
19 Vapour Pressure of Liquid @ T1 psig To be supplied by Vendor
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP
23 Inlet Pressure P1 psig
24 Specific Heat Ratio ( Cp/Cv)
25 Outlet Pressure P2 psig
26 Effective Pressure Drop DP psi
27 Calculated Cv - VTA VTA
28 % Opening VTA VTA
29 Predicted SPL dBa VTA VTA
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 2 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RTJ Flanged ASME B16.5 1500# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A105N 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A105N 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 300# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A105N 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 300# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A105N 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 300# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 300# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 300# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
10. To be confirmed by Hot Oil Heater Vendor
33 End Connections & Rating RF Flanged ASME B16.5 300# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 300# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
10. Butterfly valve shall be sized for maximum angle opening of 60 degrees.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A105N 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
10. Butterfly valve shall be sized for maximum angle opening of 60 degrees.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A105N 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
10. Butterfly valve shall be sized for maximum angle opening of 60 degrees.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material A351 CF8M 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
10. Butterfly valve shall be sized for maximum angle opening of 60 degrees.
33 End Connections & Rating RF Flanged ASME B16.600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 51.6
19 Vapour Pressure of Liquid @ T1 psig 1.45
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 7
23 Inlet Pressure P1 psig 47.7
24 Specific Heat Ratio ( Cp/Cv) 1.2
25 Outlet Pressure P2 psig 7.8
26 Effective Pressure Drop DP psi 39.9
27 Calculated Cv - VTA VTA
28 % Opening VTA VTA
29 Predicted SPL dBa VTA VTA
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 2 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 300# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216-WCB, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 300# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216-WCB, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 300# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216-WCB, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A105N, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 32.16 32.16 32.16
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.219 0.219 0.219
23 Inlet Pressure P1 psig 605 605.8 605.8
24 Specific Heat Ratio ( Cp/Cv) 1.36 1.36 1.36
25 Outlet Pressure P2 psig 22.9 23.4 23.3
26 Effective Pressure Drop DP psi 582.1 582.4 582.5
27 Calculated Cv - VTA VTA
28 % Opening VTA VTA
29 Predicted SPL dBa VTA VTA
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 1 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RTJ Flanged ASME B16.5 1500# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 42.73 42.73 42.73
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.304 0.304 0.304
23 Inlet Pressure P1 psig 994.7 996.8 1002.5
24 Specific Heat Ratio ( Cp/Cv) 1.32 1.32 1.32
25 Outlet Pressure P2 psig 22.9 23.4 23.4
26 Effective Pressure Drop DP psi 971.8 973.4 979.1
27 Calculated Cv - VTA VTA
28 % Opening VTA VTA
29 Predicted SPL dBa VTA VTA
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 1 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RTJ Flanged ASME B16.5 1500# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 2.6 2.6
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.012 0.012
23 Inlet Pressure P1 psig 615.6 616.1
24 Specific Heat Ratio ( Cp/Cv) 1.413 1.413
25 Outlet Pressure P2 psig 73.4 66.8
26 Effective Pressure Drop DP psi 542.2 549.3
27 Calculated Cv - VTA VTA
28 % Opening VTA VTA
29 Predicted SPL dBa VTA VTA
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 3 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 2.6 2.6 2.6
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.012 0.012 0.012
23 Inlet Pressure P1 psig 615.6 616.1 618.4
24 Specific Heat Ratio ( Cp/Cv) 1.413 1.413 1.413
25 Outlet Pressure P2 psig 612.8 612.4 610.1
26 Effective Pressure Drop DP psi 2.8 3.7 8.3
27 Calculated Cv - VTA VTA
28 % Opening VTA VTA
29 Predicted SPL dBa VTA VTA
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 3 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 3.7 3.7 3.7
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.014 0.014 0.014
23 Inlet Pressure P1 psig 990.3 990.6 991.9
24 Specific Heat Ratio ( Cp/Cv) 1.493 1.493 1.493
25 Outlet Pressure P2 psig 630.4 630.3 630
26 Effective Pressure Drop DP psi 359.9 360.3 361.9
27 Calculated Cv - VTA VTA
28 % Opening VTA VTA
29 Predicted SPL dBa VTA VTA
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 3 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 900# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A351 CF8M, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A351 CF8M, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 300# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 300# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A351 CF8M, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A351 CF8M, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
10. Pump recycle flow shall be confirmed by pump vendor.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A351 CF8M, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 42
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.31
23 Inlet Pressure P1 psig 871.9
24 Specific Heat Ratio ( Cp/Cv) 1.3
25 Outlet Pressure P2 psig 5.06
26 Effective Pressure Drop DP psi 866.84
27 Calculated Cv - VTA VTA
28 % Opening VTA VTA
29 Predicted SPL dBa VTA VTA
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 1 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A105N 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 66.9 66.9 66.9
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 8.822 8.822 8.822
23 Inlet Pressure P1 psig 873.4 873.7 874.9
24 Specific Heat Ratio ( Cp/Cv) 1.09 1.09 1.09
25 Outlet Pressure P2 psig 94.2 93.5 90.2
26 Effective Pressure Drop DP psi 779.2 780.2 784.7
27 Calculated Cv - VTA VTA
28 % Opening VTA VTA
29 Predicted SPL dBa VTA VTA
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 3 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type Cageg Guided (VTA)
( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 66.9
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 8.822
23 Inlet Pressure P1 psig 876.3
24 Specific Heat Ratio ( Cp/Cv) 1.09
25 Outlet Pressure P2 psig 81.7
26 Effective Pressure Drop DP psi 794.6
27 Calculated Cv - VTA
28 % Opening VTA
29 Predicted SPL dBa VTA
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 1 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A105N 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 66.9
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 8.822
23 Inlet Pressure P1 psig 876.3
24 Specific Heat Ratio ( Cp/Cv) 1.09
25 Outlet Pressure P2 psig 81.7
26 Effective Pressure Drop DP psi 794.6
27 Calculated Cv - VTA
28 % Opening VTA
29 Predicted SPL dBa VTA
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 1 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A105N 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 2.98 2.98 2.98
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.013 0.013 0.013
23 Inlet Pressure P1 psig 870.8 871.1 872.1
24 Specific Heat Ratio ( Cp/Cv) 1.471 1.471 10471
25 Outlet Pressure P2 psig 94.1 94.3 95
26 Effective Pressure Drop DP psi 776.7 776.8 777.1
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 2 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 66.9
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 8.822
23 Inlet Pressure P1 psig 876.3
24 Specific Heat Ratio ( Cp/Cv) 1.09
25 Outlet Pressure P2 psig 81.7
26 Effective Pressure Drop DP psi 794.6
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 1 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A105N 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 66.9
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 8.822
23 Inlet Pressure P1 psig 876.3
24 Specific Heat Ratio ( Cp/Cv) 1.09
25 Outlet Pressure P2 psig 81.7
26 Effective Pressure Drop DP psi 794.6
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 1 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A105N 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 0.06 0.06
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.013 0.013
23 Inlet Pressure P1 psig 4 4
24 Specific Heat Ratio ( Cp/Cv) 1.227 1.227
25 Outlet Pressure P2 psig 2.2 2.2
26 Effective Pressure Drop DP psi 1.8 1.8
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 4 inch (Hold) VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 0.06 0.06
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.013 0.013
23 Inlet Pressure P1 psig 4 4
24 Specific Heat Ratio ( Cp/Cv) 1.227 1.227
25 Outlet Pressure P2 psig 2.2 2.2
26 Effective Pressure Drop DP psi 1.8 1.8
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 4 inch (Hold) VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 66.9 66.9
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 8.822 8.822
23 Inlet Pressure P1 psig 91.8 92.1
24 Specific Heat Ratio ( Cp/Cv) 1.09 1.09
25 Outlet Pressure P2 psig 81.8 82.1
26 Effective Pressure Drop DP psi 10 10
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 1 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A105N 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 66.9 66.9
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 8.822 8.822
23 Inlet Pressure P1 psig 91.8 92.1
24 Specific Heat Ratio ( Cp/Cv) 1.09 1.09
25 Outlet Pressure P2 psig 81.8 82.1
26 Effective Pressure Drop DP psi 10 10
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 1 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A105N 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 46.25 46.25
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.684 0.684
23 Inlet Pressure P1 psig 54.07 54.07
24 Specific Heat Ratio ( Cp/Cv) 1.1 1.1
25 Outlet Pressure P2 psig 39.3 39.3
26 Effective Pressure Drop DP psi 14.77 14.77
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 4 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 300# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 0.06 0.06 0.06
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.013 0.013 0.013
23 Inlet Pressure P1 psig 83.3 83.5 84.1
24 Specific Heat Ratio ( Cp/Cv) 1.277 1.277 1.277
25 Outlet Pressure P2 psig 4.6 4.6 4.5
26 Effective Pressure Drop DP psi 78.7 78.9 79.6
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 1 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 600# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A105N, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 29.63 29.63 29.63
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 1.358 1.358 1.358
23 Inlet Pressure P1 psig 48.5 49.5 54.7
24 Specific Heat Ratio ( Cp/Cv) 1.11 1.11 1.11
25 Outlet Pressure P2 psig 9.05 8 3.34
26 Effective Pressure Drop DP psi 39.45 41.5 51.36
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 2 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 0.57 0.57
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.011 0.011
23 Inlet Pressure P1 psig 114 114
24 Specific Heat Ratio ( Cp/Cv) 1.21 1.21
25 Outlet Pressure P2 psig 11.7 10.2
26 Effective Pressure Drop DP psi 102.3 103.8
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 2 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 63.69 63.69
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 2.19 2.19
23 Inlet Pressure P1 psig 163 163
24 Specific Heat Ratio ( Cp/Cv) 1.21 1.21
25 Outlet Pressure P2 psig 153 153
26 Effective Pressure Drop DP psi 10 10
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 3 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 65.29 65.29 65.29
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 1.813 1.813 1.813
23 Inlet Pressure P1 psig 115 115 115
24 Specific Heat Ratio ( Cp/Cv) 1.21 1.21 1.21
25 Outlet Pressure P2 psig 82.5 82.5 82.3
26 Effective Pressure Drop DP psi 32.5 32.5 32.7
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 4 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 62.8 62.8
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 1.35 1.35
23 Inlet Pressure P1 psig 155.8 153.3
24 Specific Heat Ratio ( Cp/Cv) 1.21 1.21
25 Outlet Pressure P2 psig 145.6 142.6
26 Effective Pressure Drop DP psi 10.2 10.7
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 3 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 49 49
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 1.311 1.311
23 Inlet Pressure P1 psig 55.9 55.9
24 Specific Heat Ratio ( Cp/Cv) 1.1 1.1
25 Outlet Pressure P2 psig 39.4 39.4
26 Effective Pressure Drop DP psi 16.5 16.5
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 4 inch (Open) VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 300# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement No 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 0.22 0.22
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.016 0.016
23 Inlet Pressure P1 psig 18.8 18.9
24 Specific Heat Ratio ( Cp/Cv) 1.283 1.283
25 Outlet Pressure P2 psig 2 2
26 Effective Pressure Drop DP psi 16.8 16.9
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 2 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A351 CF8M, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 61.68 61.68
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.552 0.552
23 Inlet Pressure P1 psig 69.5 70.2
24 Specific Heat Ratio ( Cp/Cv) 1.2 1.2
25 Outlet Pressure P2 psig 54.3 54.3
26 Effective Pressure Drop DP psi 15.2 15.9
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 1 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 61.68
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.552
23 Inlet Pressure P1 psig 107.7
24 Specific Heat Ratio ( Cp/Cv) 1.2
25 Outlet Pressure P2 psig 40.7
26 Effective Pressure Drop DP psi 67
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 1 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A182 F316L, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 59.86
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.51
23 Inlet Pressure P1 psig 186.06
24 Specific Heat Ratio ( Cp/Cv) 1.2
25 Outlet Pressure P2 psig 30.4
26 Effective Pressure Drop DP psi 155.66
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 2 inch VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A216 WCB 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
17 Operating Temperature T1 °F
18 Density r1 @ T1 lb/ft3 59.86 59.86
19 Vapour Pressure of Liquid @ T1 psig
20 Critical Pressure of Vapor (flashing) psig
21 Critical Temp of Vapor (flashing) °F
22 Viscosity @ T1 cP 0.51 0.51
23 Inlet Pressure P1 psig 186.7 191.2
24 Specific Heat Ratio ( Cp/Cv) 1.2 1.2
25 Outlet Pressure P2 psig 176.7 174.3 Note 10
26 Effective Pressure Drop DP psi 10 16.9 Note 10
27 Calculated Cv -
28 % Opening
29 Predicted SPL dBa
30 Mfr. Model VTA VTA 56 Mfr. Model No. VTA VTA
31 Body Type Globe / Single Seated 57 Positioner Type Electro-Pneumatic (Smart)
32 Body Size Trim Size 3 inch (Hold) VTA 58 Input Signal Foundation Fieldbus (FF)
POSITIONER
33 End Connections & Rating RF Flanged ASME B16.5 150# 59 Electrical Connection 1/2" NPT
BODY
34 Body / Bonnet Material ASTM A351 CF8M, NACE 60 Pneumatic Conn. Air Supply 1/4" NPT
35 NACE Requirement Yes 61 Enclosure Type Eex i / IP 65
36 Bonnet Type Plain 62 Accessories Gauge
37 Flow Direction Up (VTA) 63
38 No. of Ports One 64
39 65 Mfr. Model No. VTA VTA
40 yp
Trim Type g Guided (VTA)
Cage ( ) 66 Set Pressure VTA
LINEAR 67 Filter Gauges Yes Yes
AIR SET
Notes :
1. VTA : Vendor to advice
2. Control valve and actuator shall be provided with 316 SS nameplate engraved with Valve Tag No., Manufacturer's Name, Model No., Valve Size & Rating.
3. Vendor shall be responsible for the proper design and selection of valve, actuator, and accessories based on the information furnished in this specification.
4. All control valves supplied shall be certified by certifying authority as per Standard Specification for Engineering and Design of Instrument Systems (SNO-I-ES-001) and
Standard Specification For Control Valves (SNO-I-ES-009).
5. Range for the gauges shall be approximately double the expected operating range of the service in which the gauge is installed. Unit for the gauges shall be in psig.
Overrange protection shall be at least 1.3 times the maximum scale reading.
6. Vendor shall refer to SNO-G-ES-008 Standard Specification Surface preparation, Painting, Galvanizing
7. Actuator and accessories shall be supplied fully assembled, tubed and tested ready for installation.
8. Vendor shall furnish sizing calculation sheet for each control valve indicating : Calculated Cv , Selected Cv, Body/port size, Noise, % Opening for calculated Cv and
Warnings e.g. Cavitation, Flashing etc.
9. Tubing and fittings material shall be 316 SS.
10. The hydraulic calculation will be confirmed during Detail Design.