Académique Documents
Professionnel Documents
Culture Documents
ivant table des bois. La stabilité des fermes doit faire l'objet d'un justification complémentaire Généralités
Les renforts longitudinaux doivent être placé avant les arbas horizontaux
La structure a été calculée avec le programme PAMIR
☒ Eléments d'antiflambement ,
4760 1240
CUILLER - Licence: 18349
180 4580 1140 100 Code de calcul: EN 1995-1-1 + DTU 31.3
Résultats de calculs complets dans la note de calculs
11 Réglages généraux
FA Epaisseur des bois (mm): 36
815
10 Poids de ferme (kg/pli): 104
Entraxe des fermes (mm): 920
40° FACTEUR SYSTÈME (KSYS): 1.1
25 Catégorie de bâtiment: Habitation
1407
FE 24 Classe de service: 2 = 65% <= H < 85%
7
FE 815 Antiflambements: Voir la table des bois
5s1 1015 2947 18
6 1342 89 1320 13 Charges (N/m²)
1000
4 FA
14 FA 12 Région de neige: A1
62 1520 Charge de neige (Sk, 202 m a.s.l): 452 N/m²
1520 FA
Pression de pointe (qp(z)): 812 N/m²
22
4624
2731
Poids propre inclus
ID Projet
Code projet : FA4A 11
Client : Client: 24
: Adresse client: , - Tel: s1 7 25 10
5 8 9 13
: Hypothèses 4
6 18 12
4624
: Site du chantier: Domont (Val-d'Oise), Neige: 3 22
A1, Vent: 2, Zone sismique: 0.00 m/s² 23
Numéro de Job : 18003-BOUYGUES-IMMO DOMONT-1- 1
LOT-1A-BAT-A1 15 a1 20
2
Type d'organisme : FA4A 14 16 17
6000 19 21
Référence de dessin :
Charges standards
Charge permanente
Toiture 470 N/m²
Sous face de prolonge 170 N/m²
Plafond 300 N/m²
Verticale d'extrémité 170 N/m²
Sous face exposée 170 N/m²
Le poids propre a été ajouté
Charge de neige
Région de neige: A1
Sk 452 N/m²
Coefficient thermique (Ct) 1
Coefficient d'exposition (Ce) 1
Altitude au dessus de la mer 202 m
Congère de neige en surplomb - Gauche Oui
Congère de neige en surplomb - Droite Oui
Retenue de neige - Gauche Non
Retenue de neige - Droite Non
Charge de vent
Région 2
Catégorie de terrain IIIA
qp(z) 812 N/m²
Largeur du bâtiment 15000 mm
Hauteur du bâtiment 20000 mm
Longueur du bâtiment 30000 mm
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 1/6
Référence du Job 18003-BOUYGUES-IMMO DOMONT-1-LOT-1A-BAT-A1 Label: FA4A 18/05/2018 - 17:13
Poids de l'homme
Poids de l'homme sur arba nominal 750 N
Poids de l'homme sur entrait nominal 750 N
Combinaisons de charges
ID Durée de Intitulé
chargement
Etat Limite Ultime
1 Permanent 1.35*Perm
4 Court terme 1.35*Perm + 1.50*Neige uniforme
25 Instantané 1.00*Perm (Soulèvement) + 1.50*Vent pignon
31 Court terme 1.35*Perm + 1.50*Homme sur l'arba gauche
42 Court terme 1.35*Perm + 1.50*Homme sur l'arba horizontal
648:4 Instantané 1.00*Perm (Soulèvement) + 1.50*Vent droite (surpr, perm 4)
649:4 Instantané 1.00*Perm (Soulèvement) + 1.50*Vent gauche (surpr, perm 4)
664:3 Instantané 1.35*Perm + 1.50*Neige uniforme + 0.90*Vent gauche (dépr, perm 3)
665:1 Instantané 1.35*Perm + 1.50*Neige uniforme + 0.90*Vent droite (dépr, perm 1)
666:1 Instantané 1.35*Perm + 0.75*Neige droite (μ1 droite, 0.5μ1 gauche) + 1.50*Vent droite (dépr, perm 1)
666:3 Instantané 1.35*Perm + 0.75*Neige droite (μ1 droite, 0.5μ1 gauche) + 1.50*Vent droite (dépr, perm 3)
667:1 Instantané 1.35*Perm + 0.75*Neige gauche (μ1 gauche, 0.5μ1 droite) + 1.50*Vent gauche (dépr, perm 1)
Etat Limite de Service
1002:2 Court terme 1.00*(Perm + Neige uniforme): Wfin
1002:4 Court terme 1.00*Neige uniforme: WQinst
1002:5 Court terme 1.00*(Perm + Neige uniforme): Wfin – WGinst
1018:2 Instantané 1.00*(Vent pignon + Perm): Wfin
1018:4 Instantané 1.00*Vent pignon: WQinst
1018:5 Instantané 1.00*(Vent pignon + Perm): Wfin – WGinst
1042:1:2 Instantané 1.00*(Perm + Vent droite (surpr, perm 1)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin
1042:1:4 Instantané 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite) + 1.00*Vent droite (surpr, perm 1): WQinst
1042:1:5 Instantané 1.00*(Perm + Vent droite (surpr, perm 1)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin – WGinst
1042:4:2 Instantané 1.00*(Perm + Vent droite (surpr, perm 4)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin
1042:4:4 Instantané 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite) + 1.00*Vent droite (surpr, perm 4): WQinst
1042:4:5 Instantané 1.00*(Perm + Vent droite (surpr, perm 4)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin – WGinst
1050:4 Court terme 1.00*Homme sur l'arba gauche: WQinst
1072:3:2 Instantané 1.00*(Perm + Vent gauche (surpr, perm 3)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin
1073:3:2 Instantané 1.00*(Perm + Vent droite (surpr, perm 3)) + 0.50*Neige droite (μ1 droite, 0.5μ1 gauche): Wfin
1078:4 Court terme 1.00*Homme sur l'arba horizontal: WQinst
1079:9:2 Instantané 1.00*(Perm + Vent gauche (dépr, perm 1)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin
1079:9:4 Instantané 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite) + 1.00*Vent gauche (dépr, perm 1): WQinst
1079:9:5 Instantané 1.00*(Perm + Vent gauche (dépr, perm 1)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin – WGinst
1082:9:2 Instantané 1.00*(Perm + Neige uniforme) + 0.60*Vent gauche (dépr, perm 1): Wfin
1082:9:4 Instantané 1.00*Neige uniforme + 0.60*Vent gauche (dépr, perm 1): WQinst
1082:9:5 Instantané 1.00*(Perm + Neige uniforme) + 0.60*Vent gauche (dépr, perm 1): Wfin – WGinst
Propriétés de matériau
Classe Emoyen Gmoyen fm,k ft,0,k ft,90,k fc,0,k fc,90,k fv,k ρk γM
N/mm² N/mm² N/mm² N/mm² N/mm² N/mm² N/mm² N/mm² kg/m³
C24 11000 690 24 14.5 0.4 21 2.5 4 350 1.3
Donnée d'appui
Noeud Y X RZ Type
Numéro N/mm N/mm kNm/rad
21 Fixe Fixe Libre Poutre périphérique en béton
a1 Fixe Libre Libre Poutre périphérique en béton
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 2/6
Référence du Job 18003-BOUYGUES-IMMO DOMONT-1-LOT-1A-BAT-A1 Label: FA4A 18/05/2018 - 17:13
Déformations maxi
Type: Combiné
Critère Autorisée Réelle CB Longueur
L/X mm L/X mm mm
Wfin 150 11.9 1080 1.6 1079:9:2 1781
Wfin - 12 - 1 1079:9:2 -
WQinst 300 5.5 1365 1.2 1078:4 1661
WQinst - 18.8 - 1 1018:4 -
Wfin – WGinst 150 11.9 1486 1.2 1079:9:5 1781
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 3/6
Référence du Job 18003-BOUYGUES-IMMO DOMONT-1-LOT-1A-BAT-A1 Label: FA4A 18/05/2018 - 17:13
Connecteurs
Type de Fabriqué par Certificat d'approbation
connecteur
M20 MiTek Royaume uni TRADA TE//F08550-M20 V1
Structure
Noeud Réelle Largeur requise Cb Aire efficace requise kc90 fc,k Résistance des bois Résistance des plaques Taux de travail
Numéro mm mm mm² N/mm² N N %
21 200 20 667:1 2160 1.50 2.5 32670 0 22.9
a1 160 38 1 1368 1.50 5.7 13835 0 28.1
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 4/6
Référence du Job 18003-BOUYGUES-IMMO DOMONT-1-LOT-1A-BAT-A1 Label: FA4A 18/05/2018 - 17:13
Déformation globale
Type: Combiné
Bois Critère Autorisée Absolu Longueur Ratio Déformation Ratio CB
Nœuds L/X mm mm L/X mm %
a1-1 Wfin 200 3 161 - - - 1079:9:2
a1-11 Wfin 200 30.1 6028 2115 2.8 9.5 1079:9:2
5-12 Wfin 200 14.2 2831 10627 0.3 1.9 1079:9:2
14-21 Wfin 200 28.1 5625 3999 1.4 5.1 1079:9:2
a1-1 WQinst 300 3 161 - - - 1018:4
a1-11 WQinst 300 20.1 6028 3494 1.7 8.6 1018:4
5-12 WQinst 300 9.4 2831 2235 1.3 13.5 1078:4
14-21 WQinst 300 18.8 5625 12012 0.5 2.5 1018:4
a1-1 Wfin – WGinst 200 3 161 - - - 1079:9:5
a1-11 Wfin – WGinst 200 30.1 6028 2997 2 6.7 1079:9:5
5-12 Wfin – WGinst 200 14.2 2831 19758 0.1 1.1 1079:9:5
14-21 Wfin – WGinst 350 16.1 5625 6619 0.8 5.3 1079:9:5
Déformation locale
Type: Combiné
Bois Critère Autorisée Absolu Longueur Relative Déformation Ratio CB
Nœuds L/X mm mm L/X mm %
a1-1 Wfin 150 3 161 - - - 1079:9:2
a1-2 Wfin 150 3 95 31850 0 - 1079:9:2
2-3 Wfin 150 11.8 1763 1430 1.2 10.5 1079:9:2
3-5 Wfin 150 11.7 1757 5512 0.3 2.8 1079:9:2
5-6 Wfin 150 3.3 489 1322 0.4 11.4 1079:9:2
6-10 Wfin 150 11.9 1781 1080 1.6 13.9 1079:9:2
10-11 Wfin 150 3 144 142641 0 - 1079:9:2
5-8 Wfin 150 11.1 1661 8936 0.2 1.7 1079:9:2
8-12 Wfin 150 7.4 1103 10510 0.1 1.5 1079:9:2
19-21 Wfin 200 5.7 1143 31603 0 0.7 1073:3:2
17-19 Wfin 200 8.7 1743 4873 0.4 4.2 1079:9:2
16-17 Wfin 200 6.8 1352 20919 0.1 1.0 1079:9:2
15-16 Wfin 200 6.5 1307 10633 0.1 1.9 1018:2
14-15 Wfin 200 3 81 - - - 1079:9:2
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 5/6
Référence du Job 18003-BOUYGUES-IMMO DOMONT-1-LOT-1A-BAT-A1 Label: FA4A 18/05/2018 - 17:13
Déformation locale
Type: Combiné
Bois Critère Autorisée Absolu Longueur Relative Déformation Ratio CB
Nœuds L/X mm mm L/X mm %
a1-1 WQinst 300 3 161 - - - 1018:4
a1-2 WQinst 300 3 95 - - - 1079:9:4
2-3 WQinst 300 5.9 1763 2831 0.6 10.6 1018:4
3-5 WQinst 300 5.9 1757 8154 0.2 3.7 1079:9:4
5-6 WQinst 300 3 489 1905 0.3 8.6 1018:4
6-10 WQinst 300 5.9 1781 1620 1.1 18.6 1018:4
10-11 WQinst 300 3 144 - - - 1079:9:4
5-8 WQinst 300 5.5 1661 1365 1.2 22.0 1078:4
8-12 WQinst 300 3.7 1103 8511 0.1 3.6 1078:4
19-21 WQinst 300 3.8 1143 96862 0 0.4 1079:9:4
17-19 WQinst 300 5.8 1743 26409 0.1 1.2 1018:4
16-17 WQinst 300 4.5 1352 59204 0 0.6 1018:4
15-16 WQinst 300 4.4 1307 87566 0 0.4 1018:4
14-15 WQinst 300 3 81 - - - 1082:9:4
a1-1 Wfin – WGinst 150 3 161 - - - 1079:9:5
a1-2 Wfin – WGinst 150 3 95 55832 0 - 1079:9:5
2-3 Wfin – WGinst 150 11.8 1763 2038 0.9 7.4 1079:9:5
3-5 Wfin – WGinst 150 11.7 1757 6722 0.3 2.3 1079:9:5
5-6 Wfin – WGinst 150 3.3 489 1774 0.3 8.5 1079:9:5
6-10 Wfin – WGinst 150 11.9 1781 1486 1.2 10.1 1079:9:5
10-11 Wfin – WGinst 150 3 144 - - - 1079:9:5
5-8 Wfin – WGinst 150 11.1 1661 16716 0.1 0.9 1079:9:5
8-12 Wfin – WGinst 150 7.4 1103 16004 0.1 1.0 1079:9:5
19-21 Wfin – WGinst 350 3.3 1143 53502 0 0.7 1042:4:5
17-19 Wfin – WGinst 350 5 1743 9126 0.2 3.9 1079:9:5
16-17 Wfin – WGinst 350 3.9 1352 35062 0 1.0 1079:9:5
15-16 Wfin – WGinst 350 3.7 1307 21264 0.1 1.7 1018:5
14-15 Wfin – WGinst 350 3 81 - - - 1082:9:5
Labels de production
Label
B1
C1
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 6/6
FA4C - 7nb.1-pli Distances d'antiflambement suivant table des bois. La stabilité des fermes doit faire l'objet d'un justification complémentaire Généralités
Les renforts longitudinaux doivent être placé avant les arbas horizontaux
La structure a été calculée avec le programme PAMIR
☒ Eléments d'antiflambement ,
4760 2340
CUILLER - Licence: 18349
180 4580 2240 100 Code de calcul: EN 1995-1-1 + DTU 31.3
Résultats de calculs complets dans la note de calculs
11 Réglages généraux
FA Epaisseur des bois (mm): 36
815
10 Poids de ferme (kg/pli): 125
Entraxe des fermes (mm): 920
40° FACTEUR SYSTÈME (KSYS): 1.1
27 Catégorie de bâtiment: Habitation
1407
FE 26 Classe de service: 2 = 65% <= H < 85%
7
FE 815 Antiflambements: Voir la table des bois
5s1 1015 194047
6 1342 89 1520 14 Charges (N/m²)
1000
4 1320
FA
14 FA 13 Région de neige: A1
62 1520 12 FA Charge de neige (Sk, 202 m a.s.l): 452 N/m²
1520 FA
Pression de pointe (qp(z)): 812 N/m²
24
4624
2731
Réactions d'appui (N) (Ultime)
Nœud Dir. Perm Moyen Court Inst Inst Caract. APPUI
No Max Max Max Max Min MAX / MIN mm
1 FA
80
ID Projet
Code projet : FA4C 11
Client : Client: 26
: Adresse client: , - Tel: s1 7 27 10
5 89 14
: Hypothèses 4
6 19 12 13
4624
: Site du chantier: Domont (Val-d'Oise), Neige: 3 24
A1, Vent: 2, Zone sismique: 0.00 m/s² 25
Numéro de Job : 18003-BOUYGUES-IMMO DOMONT-1- 1
LOT-1A-BAT-A1 16 a1 21 22
2
Type d'organisme : FA4C 15 17 187100 20 23
Référence de dessin : s2
Charges standards
Charge permanente
Toiture 470 N/m²
Sous face de prolonge 170 N/m²
Plafond 300 N/m²
Sous face exposée 170 N/m²
Le poids propre a été ajouté
Charge de neige
Région de neige: A1
Sk 452 N/m²
Coefficient thermique (Ct) 1
Coefficient d'exposition (Ce) 1
Altitude au dessus de la mer 202 m
Congère de neige en surplomb - Gauche Oui
Congère de neige en surplomb - Droite Oui
Retenue de neige - Gauche Non
Retenue de neige - Droite Non
Charge de vent
Région 2
Catégorie de terrain IIIA
qp(z) 812 N/m²
Largeur du bâtiment 15000 mm
Hauteur du bâtiment 20000 mm
Longueur du bâtiment 30000 mm
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 1/7
Référence du Job 18003-BOUYGUES-IMMO DOMONT-1-LOT-1A-BAT-A1 Label: FA4C 21/05/2018 - 09:38
Poids de l'homme
Poids de l'homme sur arba nominal 750 N
Poids de l'homme sur entrait nominal 750 N
Combinaisons de charges
ID Durée de Intitulé
chargement
Etat Limite Ultime
1 Permanent 1.35*Perm
4 Court terme 1.35*Perm + 1.50*Neige uniforme
25 Instantané 1.00*Perm (Soulèvement) + 1.50*Vent pignon
31 Court terme 1.35*Perm + 1.50*Homme sur l'arba gauche
42 Court terme 1.35*Perm + 1.50*Homme sur l'arba horizontal
648:4 Instantané 1.00*Perm (Soulèvement) + 1.50*Vent droite (surpr, perm 4)
649:4 Instantané 1.00*Perm (Soulèvement) + 1.50*Vent gauche (surpr, perm 4)
664:3 Instantané 1.35*Perm + 1.50*Neige uniforme + 0.90*Vent gauche (dépr, perm 3)
665:1 Instantané 1.35*Perm + 1.50*Neige uniforme + 0.90*Vent droite (dépr, perm 1)
666:1 Instantané 1.35*Perm + 0.75*Neige droite (μ1 droite, 0.5μ1 gauche) + 1.50*Vent droite (dépr, perm 1)
666:3 Instantané 1.35*Perm + 0.75*Neige droite (μ1 droite, 0.5μ1 gauche) + 1.50*Vent droite (dépr, perm 3)
667:1 Instantané 1.35*Perm + 0.75*Neige gauche (μ1 gauche, 0.5μ1 droite) + 1.50*Vent gauche (dépr, perm 1)
Etat Limite de Service
1002:2 Court terme 1.00*(Perm + Neige uniforme): Wfin
1002:4 Court terme 1.00*Neige uniforme: WQinst
1002:5 Court terme 1.00*(Perm + Neige uniforme): Wfin – WGinst
1018:2 Instantané 1.00*(Vent pignon + Perm): Wfin
1018:4 Instantané 1.00*Vent pignon: WQinst
1018:5 Instantané 1.00*(Vent pignon + Perm): Wfin – WGinst
1042:1:2 Instantané 1.00*(Perm + Vent droite (surpr, perm 1)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin
1042:1:4 Instantané 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite) + 1.00*Vent droite (surpr, perm 1): WQinst
1042:1:5 Instantané 1.00*(Perm + Vent droite (surpr, perm 1)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin – WGinst
1042:4:2 Instantané 1.00*(Perm + Vent droite (surpr, perm 4)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin
1042:4:4 Instantané 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite) + 1.00*Vent droite (surpr, perm 4): WQinst
1042:4:5 Instantané 1.00*(Perm + Vent droite (surpr, perm 4)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin – WGinst
1050:4 Court terme 1.00*Homme sur l'arba gauche: WQinst
1072:3:2 Instantané 1.00*(Perm + Vent gauche (surpr, perm 3)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin
1073:3:2 Instantané 1.00*(Perm + Vent droite (surpr, perm 3)) + 0.50*Neige droite (μ1 droite, 0.5μ1 gauche): Wfin
1078:4 Court terme 1.00*Homme sur l'arba horizontal: WQinst
1079:9:2 Instantané 1.00*(Perm + Vent gauche (dépr, perm 1)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin
1079:9:4 Instantané 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite) + 1.00*Vent gauche (dépr, perm 1): WQinst
1079:9:5 Instantané 1.00*(Perm + Vent gauche (dépr, perm 1)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin – WGinst
1082:9:2 Instantané 1.00*(Perm + Neige uniforme) + 0.60*Vent gauche (dépr, perm 1): Wfin
1082:9:4 Instantané 1.00*Neige uniforme + 0.60*Vent gauche (dépr, perm 1): WQinst
1082:9:5 Instantané 1.00*(Perm + Neige uniforme) + 0.60*Vent gauche (dépr, perm 1): Wfin – WGinst
Propriétés de matériau
Classe Emoyen Gmoyen fm,k ft,0,k ft,90,k fc,0,k fc,90,k fv,k ρk γM
N/mm² N/mm² N/mm² N/mm² N/mm² N/mm² N/mm² N/mm² kg/m³
C24 11000 690 24 14.5 0.4 21 2.5 4 350 1.3
Donnée d'appui
Noeud Y X RZ Type
Numéro N/mm N/mm kNm/rad
23 Fixe Fixe Libre Poutre périphérique en béton
a1 Fixe Libre Libre Poutre périphérique en béton
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 2/7
Référence du Job 18003-BOUYGUES-IMMO DOMONT-1-LOT-1A-BAT-A1 Label: FA4C 21/05/2018 - 09:38
Déformations maxi
Type: Combiné
Critère Autorisée Réelle CB Longueur
L/X mm L/X mm mm
Wfin 150 11.9 1077 1.7 1079:9:2 1782
Wfin - 12 - 1.3 1079:9:2 -
WQinst 300 5.5 1360 1.2 1078:4 1661
WQinst - 22.6 - 1.3 1018:4 -
Wfin – WGinst 150 11.9 1483 1.2 1079:9:5 1782
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 3/7
Référence du Job 18003-BOUYGUES-IMMO DOMONT-1-LOT-1A-BAT-A1 Label: FA4C 21/05/2018 - 09:38
Connecteurs
Type de Fabriqué par Certificat d'approbation
connecteur
M20 MiTek Royaume uni TRADA TE//F08550-M20 V1
Structure
Noeud Réelle Largeur requise Cb Aire efficace requise kc90 fc,k Résistance des bois Résistance des plaques Taux de travail
Numéro mm mm mm² N/mm² N N %
23 200 18 667:1 1944 1.50 2.5 32670 0 20.1
a1 160 43 1 1548 1.50 5.7 13835 0 31.7
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 4/7
Référence du Job 18003-BOUYGUES-IMMO DOMONT-1-LOT-1A-BAT-A1 Label: FA4C 21/05/2018 - 09:38
Déformation globale
Type: Combiné
Bois Critère Autorisée Absolu Longueur Ratio Déformation Ratio CB
Nœuds L/X mm mm L/X mm %
a1-1 Wfin 200 3 161 - - - 1079:9:2
a1-11 Wfin 200 30.1 6028 2117 2.8 9.5 1079:9:2
5-13 Wfin 200 19.5 3892 9820 0.4 2.1 1079:9:2
15-23 Wfin 200 33.8 6767 3467 2 5.8 1079:9:2
a1-1 WQinst 300 3 161 - - - 1018:4
a1-11 WQinst 300 20.1 6028 3542 1.7 8.5 1018:4
5-13 WQinst 300 13 3892 3035 1.3 9.9 1078:4
15-23 WQinst 300 22.6 6767 10120 0.7 3.0 1018:4
a1-1 Wfin – WGinst 200 3 161 - - - 1079:9:5
a1-11 Wfin – WGinst 200 30.1 6028 3016 2 6.7 1079:9:5
5-13 Wfin – WGinst 200 19.5 3892 16700 0.2 1.2 1079:9:5
15-23 Wfin – WGinst 350 19.3 6767 5701 1.2 6.2 1079:9:5
Déformation locale
Type: Combiné
Bois Critère Autorisée Absolu Longueur Relative Déformation Ratio CB
Nœuds L/X mm mm L/X mm %
a1-1 Wfin 150 3 161 - - - 1079:9:2
a1-2 Wfin 150 3 102 24340 0 0.2 1079:9:2
2-3 Wfin 150 11.7 1749 1327 1.3 11.4 1079:9:2
3-5 Wfin 150 11.7 1762 6665 0.3 2.3 1079:9:2
5-6 Wfin 150 3.3 489 1416 0.3 10.6 1079:9:2
6-10 Wfin 150 11.9 1782 1077 1.7 14.0 1079:9:2
10-11 Wfin 150 3 144 142653 0 - 1079:9:2
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 5/7
Référence du Job 18003-BOUYGUES-IMMO DOMONT-1-LOT-1A-BAT-A1 Label: FA4C 21/05/2018 - 09:38
Déformation locale
Type: Combiné
Bois Critère Autorisée Absolu Longueur Relative Déformation Ratio CB
Nœuds L/X mm mm L/X mm %
5-8 Wfin 150 11.1 1661 9760 0.2 1.6 1079:9:2
8-12 Wfin 150 7.4 1109 15476 0.1 1.0 1079:9:2
12-13 Wfin 150 7.1 1061 4876 0.2 3.1 1079:9:2
21-23 Wfin 200 5.5 1100 23533 0 0.9 1018:2
20-21 Wfin 200 5.9 1184 7581 0.2 2.7 1079:9:2
18-20 Wfin 200 8.7 1735 5569 0.3 3.6 1079:9:2
17-18 Wfin 200 6.8 1353 23760 0.1 0.9 1079:9:2
16-17 Wfin 200 6.6 1313 10509 0.1 2.0 1018:2
15-16 Wfin 200 3 81 - - - 1072:3:2
a1-1 WQinst 300 3 161 - - - 1018:4
a1-2 WQinst 300 3 102 97751 0 - 1079:9:4
2-3 WQinst 300 5.8 1749 2658 0.7 11.3 1018:4
3-5 WQinst 300 5.9 1762 9180 0.2 3.3 1079:9:4
5-6 WQinst 300 3 489 1986 0.2 8.3 1018:4
6-10 WQinst 300 5.9 1782 1620 1.1 18.6 1018:4
10-11 WQinst 300 3 144 - - - 1079:9:4
5-8 WQinst 300 5.5 1661 1360 1.2 22.1 1078:4
8-12 WQinst 300 3.7 1109 8891 0.1 3.4 1078:4
12-13 WQinst 300 3.5 1061 10756 0.1 2.8 1018:4
21-23 WQinst 300 3.7 1100 22914 0 1.4 1018:4
20-21 WQinst 300 3.9 1184 19537 0.1 1.6 1018:4
18-20 WQinst 300 5.8 1735 36725 0 0.9 1018:4
17-18 WQinst 300 4.5 1353 69984 0 0.5 1018:4
16-17 WQinst 300 4.4 1313 86015 0 0.4 1018:4
15-16 WQinst 300 3 81 - - - 1079:9:4
a1-1 Wfin – WGinst 150 3 161 - - - 1079:9:5
a1-2 Wfin – WGinst 150 3 102 41766 0 - 1079:9:5
2-3 Wfin – WGinst 150 11.7 1749 1902 0.9 7.9 1079:9:5
3-5 Wfin – WGinst 150 11.7 1762 7902 0.2 1.9 1079:9:5
5-6 Wfin – WGinst 150 3.3 489 1883 0.3 8.0 1079:9:5
6-10 Wfin – WGinst 150 11.9 1782 1483 1.2 10.2 1079:9:5
10-11 Wfin – WGinst 150 3 144 - - - 1079:9:5
5-8 Wfin – WGinst 150 11.1 1661 17879 0.1 0.9 1079:9:5
8-12 Wfin – WGinst 150 7.4 1109 23063 0 0.7 1079:9:5
12-13 Wfin – WGinst 150 7.1 1061 7713 0.1 2.0 1079:9:5
21-23 Wfin – WGinst 350 3.1 1100 23287 0 1.6 1018:5
20-21 Wfin – WGinst 350 3.4 1184 12253 0.1 2.9 1079:9:5
18-20 Wfin – WGinst 350 5 1735 10755 0.2 3.3 1079:9:5
17-18 Wfin – WGinst 350 3.9 1353 40114 0 0.9 1079:9:5
16-17 Wfin – WGinst 350 3.8 1313 21715 0.1 1.7 1018:5
15-16 Wfin – WGinst 350 3 81 - - - 1082:9:5
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 6/7
Référence du Job 18003-BOUYGUES-IMMO DOMONT-1-LOT-1A-BAT-A1 Label: FA4C 21/05/2018 - 09:38
Labels de production
Label
B2
C2
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 7/7
FA4D - 1nb.1-pli Distances d'antiflambement suivant table des bois. La stabilité des fermes doit faire l'objet d'un justification complémentaire Généralités
Les renforts longitudinaux doivent être placé avant les arbas horizontaux
La structure a été calculée avec le programme PAMIR
☒ Eléments d'antiflambement ,
4760 2340
CUILLER - Licence: 18349
180 4580 1640 700 Code de calcul: EN 1995-1-1 + DTU 31.3
Résultats de calculs complets dans la note de calculs
11 Réglages généraux
FA Epaisseur des bois (mm): 36
815
10 Poids de ferme (kg/pli): 119
Entraxe des fermes (mm): 920
40° FACTEUR SYSTÈME (KSYS): 1.1
27 Catégorie de bâtiment: Habitation
1407
FE 26 Classe de service: 2 = 65% <= H < 85%
7
FE 815 Antiflambements: Voir la table des bois
5s1 1015 194047
6 1342 89 1320 14 Charges (N/m²)
1000
4 1320
FA FA
14 FA 13 Région de neige: A1
62 1520 12 Charge de neige (Sk, 202 m a.s.l): 452 N/m²
1520 FA
Pression de pointe (qp(z)): 812 N/m²
24
4624
2731
Réactions d'appui (N) (Ultime)
Nœud Dir. Perm Moyen Court Inst Inst Caract. APPUI
No Max Max Max Max Min MAX / MIN mm
1 FA
80
ID Projet
Code projet : FA4D 11
Client : Client: 26
: Adresse client: , - Tel: s1 7 27 10
5 89 14
: Hypothèses 4
6 19
4624
: Site du chantier: Domont (Val-d'Oise), Neige: 3 24 12 13
A1, Vent: 2, Zone sismique: 0.00 m/s² 25
Numéro de Job : 18003-BOUYGUES-IMMO DOMONT-1- 1
LOT-1A-BAT-A1 16 a1
2 21 22
Type d'organisme : FA4D 15 17 187100 20 a2 23
Référence de dessin : s2
Charges standards
Charge permanente
Toiture 470 N/m²
Sous face de prolonge 170 N/m²
Plafond 300 N/m²
Sous face exposée 170 N/m²
Le poids propre a été ajouté
Charge de neige
Région de neige: A1
Sk 452 N/m²
Coefficient thermique (Ct) 1
Coefficient d'exposition (Ce) 1
Altitude au dessus de la mer 202 m
Congère de neige en surplomb - Gauche Oui
Congère de neige en surplomb - Droite Oui
Retenue de neige - Gauche Non
Retenue de neige - Droite Non
Charge de vent
Région 2
Catégorie de terrain IIIA
qp(z) 812 N/m²
Largeur du bâtiment 15000 mm
Hauteur du bâtiment 20000 mm
Longueur du bâtiment 30000 mm
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 1/7
Référence du Job 18003-BOUYGUES-IMMO DOMONT-1-LOT-1A-BAT-A1 Label: FA4D 22/05/2018 - 10:40
Poids de l'homme
Poids de l'homme sur arba nominal 750 N
Poids de l'homme sur entrait nominal 750 N
Combinaisons de charges
ID Durée de Intitulé
chargement
Etat Limite Ultime
1 Permanent 1.35*Perm
4 Court terme 1.35*Perm + 1.50*Neige uniforme
25 Instantané 1.00*Perm (Soulèvement) + 1.50*Vent pignon
31 Court terme 1.35*Perm + 1.50*Homme sur l'arba gauche
42 Court terme 1.35*Perm + 1.50*Homme sur l'arba horizontal
648:4 Instantané 1.00*Perm (Soulèvement) + 1.50*Vent droite (surpr, perm 4)
649:4 Instantané 1.00*Perm (Soulèvement) + 1.50*Vent gauche (surpr, perm 4)
664:3 Instantané 1.35*Perm + 1.50*Neige uniforme + 0.90*Vent gauche (dépr, perm 3)
665:1 Instantané 1.35*Perm + 1.50*Neige uniforme + 0.90*Vent droite (dépr, perm 1)
666:1 Instantané 1.35*Perm + 0.75*Neige droite (μ1 droite, 0.5μ1 gauche) + 1.50*Vent droite (dépr, perm 1)
666:3 Instantané 1.35*Perm + 0.75*Neige droite (μ1 droite, 0.5μ1 gauche) + 1.50*Vent droite (dépr, perm 3)
667:1 Instantané 1.35*Perm + 0.75*Neige gauche (μ1 gauche, 0.5μ1 droite) + 1.50*Vent gauche (dépr, perm 1)
Etat Limite de Service
1002:2 Court terme 1.00*(Perm + Neige uniforme): Wfin
1002:4 Court terme 1.00*Neige uniforme: WQinst
1002:5 Court terme 1.00*(Perm + Neige uniforme): Wfin – WGinst
1018:2 Instantané 1.00*(Vent pignon + Perm): Wfin
1018:4 Instantané 1.00*Vent pignon: WQinst
1018:5 Instantané 1.00*(Vent pignon + Perm): Wfin – WGinst
1042:1:2 Instantané 1.00*(Perm + Vent droite (surpr, perm 1)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin
1042:1:4 Instantané 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite) + 1.00*Vent droite (surpr, perm 1): WQinst
1042:1:5 Instantané 1.00*(Perm + Vent droite (surpr, perm 1)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin – WGinst
1042:4:2 Instantané 1.00*(Perm + Vent droite (surpr, perm 4)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin
1042:4:4 Instantané 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite) + 1.00*Vent droite (surpr, perm 4): WQinst
1042:4:5 Instantané 1.00*(Perm + Vent droite (surpr, perm 4)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin – WGinst
1050:4 Court terme 1.00*Homme sur l'arba gauche: WQinst
1072:3:2 Instantané 1.00*(Perm + Vent gauche (surpr, perm 3)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin
1073:3:2 Instantané 1.00*(Perm + Vent droite (surpr, perm 3)) + 0.50*Neige droite (μ1 droite, 0.5μ1 gauche): Wfin
1078:4 Court terme 1.00*Homme sur l'arba horizontal: WQinst
1079:9:2 Instantané 1.00*(Perm + Vent gauche (dépr, perm 1)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin
1079:9:4 Instantané 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite) + 1.00*Vent gauche (dépr, perm 1): WQinst
1079:9:5 Instantané 1.00*(Perm + Vent gauche (dépr, perm 1)) + 0.50*Neige gauche (μ1 gauche, 0.5μ1 droite): Wfin – WGinst
1082:9:2 Instantané 1.00*(Perm + Neige uniforme) + 0.60*Vent gauche (dépr, perm 1): Wfin
1082:9:4 Instantané 1.00*Neige uniforme + 0.60*Vent gauche (dépr, perm 1): WQinst
1082:9:5 Instantané 1.00*(Perm + Neige uniforme) + 0.60*Vent gauche (dépr, perm 1): Wfin – WGinst
Propriétés de matériau
Classe Emoyen Gmoyen fm,k ft,0,k ft,90,k fc,0,k fc,90,k fv,k ρk γM
N/mm² N/mm² N/mm² N/mm² N/mm² N/mm² N/mm² N/mm² kg/m³
C24 11000 690 24 14.5 0.4 21 2.5 4 350 1.3
Donnée d'appui
Noeud Y X RZ Type
Numéro N/mm N/mm kNm/rad
15 Fixe Libre Libre Etrier
23 Fixe Fixe Libre Poutre périphérique en béton
a1 Fixe Libre Libre Poutre périphérique en béton
a2 Fixe Libre Libre Poutre périphérique en béton
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 2/7
Référence du Job 18003-BOUYGUES-IMMO DOMONT-1-LOT-1A-BAT-A1 Label: FA4D 22/05/2018 - 10:40
Déformations maxi
Type: Combiné
Critère Autorisée Réelle CB Longueur
L/X mm L/X mm mm
Wfin 150 11.9 1079 1.7 1079:9:2 1782
Wfin - 12 - 2.5 1079:9:2 -
WQinst 300 5.5 1364 1.2 1078:4 1661
WQinst - 20.3 - 1.7 1018:4 -
Wfin – WGinst 350 17.4 3182 1.9 1079:9:5 6086
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 3/7
Référence du Job 18003-BOUYGUES-IMMO DOMONT-1-LOT-1A-BAT-A1 Label: FA4D 22/05/2018 - 10:40
Connecteurs
Type de Fabriqué par Certificat d'approbation
connecteur
M20 MiTek Royaume uni TRADA TE//F08550-M20 V1
Structure
Noeud Réelle Largeur requise Cb Aire efficace requise kc90 fc,k Résistance des bois Résistance des plaques Taux de travail
Numéro mm mm mm² N/mm² N N %
15 100 17 667:1 1836 1.50 2.5 16335 0 37.1
23 200 3 25 324 1.50 2.5 32670 0 2.5
a1 160 9 25 324 1.50 5.7 25365 0 6.7
a2 200 25 667:1 2700 1.50 2.5 32670 0 28.3
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 4/7
Référence du Job 18003-BOUYGUES-IMMO DOMONT-1-LOT-1A-BAT-A1 Label: FA4D 22/05/2018 - 10:40
Déformation globale
Type: Combiné
Bois Critère Autorisée Absolu Longueur Ratio Déformation Ratio CB
Nœuds L/X mm mm L/X mm %
a1-1 Wfin 200 3 161 - - - 1079:9:2
a1-11 Wfin 200 30.1 6028 2143 2.8 9.4 1079:9:2
5-13 Wfin 200 16.7 3331 1870 1.8 10.7 1079:9:2
a2-23 Wfin 200 3.1 613 4031 0.2 5.0 1079:9:2
a2-15 Wfin 200 30.4 6086 2049 3 9.8 1079:9:2
a1-1 WQinst 300 3 161 - - - 1018:4
a1-11 WQinst 300 20.1 6028 3546 1.7 8.5 1018:4
5-13 WQinst 300 11.1 3331 2541 1.3 11.9 1078:4
a2-23 WQinst 300 3 613 8202 0.1 2.5 1018:4
a2-15 WQinst 300 20.3 6086 4378 1.4 6.9 1018:4
a1-1 Wfin – WGinst 200 3 161 - - - 1079:9:5
a1-11 Wfin – WGinst 200 30.1 6028 3043 2 6.6 1079:9:5
5-13 Wfin – WGinst 200 16.7 3331 2894 1.2 7.0 1079:9:5
a2-23 Wfin – WGinst 350 3 613 6068 0.1 3.4 1079:9:5
a2-15 Wfin – WGinst 350 17.4 6086 3182 1.9 11.1 1079:9:5
Déformation locale
Type: Combiné
Bois Critère Autorisée Absolu Longueur Relative Déformation Ratio CB
Nœuds L/X mm mm L/X mm %
a1-1 Wfin 150 3 161 - - - 1079:9:2
a1-2 Wfin 150 3 102 - - - 1018:2
2-3 Wfin 150 11.7 1749 2278 0.8 6.6 1079:9:2
3-5 Wfin 150 11.7 1762 4280 0.4 3.6 1079:9:2
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 5/7
Référence du Job 18003-BOUYGUES-IMMO DOMONT-1-LOT-1A-BAT-A1 Label: FA4D 22/05/2018 - 10:40
Déformation locale
Type: Combiné
Bois Critère Autorisée Absolu Longueur Relative Déformation Ratio CB
Nœuds L/X mm mm L/X mm %
5-6 Wfin 150 3.3 489 1312 0.4 11.5 1079:9:2
6-10 Wfin 150 11.9 1782 1079 1.7 14.0 1079:9:2
10-11 Wfin 150 3 144 142619 0 - 1079:9:2
5-8 Wfin 150 11.1 1661 14210 0.1 1.1 1082:9:2
8-12 Wfin 150 7.4 1109 4478 0.2 3.4 1079:9:2
12-13 Wfin 150 3.3 500 5571 0.1 2.7 1042:1:2
a2-23 Wfin 200 3.1 613 4031 0.2 5.0 1079:9:2
a2-21 Wfin 200 3 554 9674 0.1 2.0 1079:9:2
20-21 Wfin 200 5.7 1130 2909 0.4 6.9 1079:9:2
18-20 Wfin 200 8.7 1735 7002 0.2 2.9 1079:9:2
17-18 Wfin 200 6.8 1353 17085 0.1 1.2 1079:9:2
15-17 Wfin 200 6.6 1313 8882 0.1 2.3 1082:9:2
a1-1 WQinst 300 3 161 - - - 1018:4
a1-2 WQinst 300 3 102 - - - 1018:4
2-3 WQinst 300 5.8 1749 3650 0.5 8.3 1018:4
3-5 WQinst 300 5.9 1762 7377 0.2 4.1 1079:9:4
5-6 WQinst 300 3 489 1904 0.3 8.6 1018:4
6-10 WQinst 300 5.9 1782 1620 1.1 18.6 1018:4
10-11 WQinst 300 3 144 - - - 1079:9:4
5-8 WQinst 300 5.5 1661 1364 1.2 22.0 1078:4
8-12 WQinst 300 3.7 1109 9099 0.1 3.3 1018:4
12-13 WQinst 300 3 500 6150 0.1 2.8 1018:4
a2-23 WQinst 300 3 613 8202 0.1 2.5 1018:4
a2-21 WQinst 300 3 554 18777 0 1.0 1018:4
20-21 WQinst 300 3.8 1130 6213 0.2 4.9 1018:4
18-20 WQinst 300 5.8 1735 75013 0 0.4 1079:9:4
17-18 WQinst 300 4.5 1353 47809 0 0.7 1018:4
15-17 WQinst 300 4.4 1313 183783 0 0.2 1082:9:4
a1-1 Wfin – WGinst 150 3 161 - - - 1079:9:5
a1-2 Wfin – WGinst 150 3 102 - - - 1018:5
2-3 Wfin – WGinst 150 11.7 1749 3013 0.6 5.0 1079:9:5
3-5 Wfin – WGinst 150 11.7 1762 5602 0.3 2.7 1079:9:5
5-6 Wfin – WGinst 150 3.3 489 1762 0.3 8.6 1079:9:5
6-10 Wfin – WGinst 150 11.9 1782 1484 1.2 10.2 1079:9:5
10-11 Wfin – WGinst 150 3 144 - - - 1079:9:5
5-8 Wfin – WGinst 150 11.1 1661 28352 0.1 0.6 1082:9:5
8-12 Wfin – WGinst 150 7.4 1109 6801 0.2 2.3 1079:9:5
12-13 Wfin – WGinst 150 3.3 500 7957 0.1 1.9 1042:1:5
a2-23 Wfin – WGinst 350 3 613 6068 0.1 3.4 1079:9:5
a2-21 Wfin – WGinst 350 3 554 14988 0 1.3 1079:9:5
20-21 Wfin – WGinst 350 3.2 1130 4559 0.2 7.7 1079:9:5
18-20 Wfin – WGinst 350 5 1735 14372 0.1 2.5 1079:9:5
17-18 Wfin – WGinst 350 3.9 1353 28200 0 1.3 1079:9:5
15-17 Wfin – WGinst 350 3.8 1313 19090 0.1 1.9 1082:9:5
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 6/7
Référence du Job 18003-BOUYGUES-IMMO DOMONT-1-LOT-1A-BAT-A1 Label: FA4D 22/05/2018 - 10:40
Labels de production
Label
B3
C2
Pamir de MiTek - Exécuté par CUILLER - Licence: 18349 - Pamir Version 7.0b - Utilisateur : MiTek_FR Page 7/7