Académique Documents
Professionnel Documents
Culture Documents
Technical
Publication
Important Precautions
- iii
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
iv -
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
- v
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
vi -
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
- vii
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
viii -
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
- ix
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
DAMAGE IN TRANSPORTATION
All packages should be closely examined at time of delivery. If damage is apparent write “Damage In
Shipment” on ALL copies of the freight or express bill BEFORE delivery is accepted or “signed for” by
a GE representative or hospital receiving agent. Whether noted or concealed, damage MUST be
reported to the carrier immediately upon discovery, or in any event, within 14 days after receipt, and the
contents and containers held for inspection by the carrier. A transportation company will not pay a claim
for damage if an inspection is not requested within this 14 day period.
GE Healthcare employees should use the iTrak System to report all documentation errors or omissions.
x -
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
LEGAL NOTES
The contents of this publication may not be copied or duplicated in any form, in whole or in part, without
prior written permission of GE Healthcare.
TRADEMARKS
All products and their name brands are trademarks of their respective holders.
COPYRIGHTS
All Material Copyright© 2008-2009 by General Electric Inc. All Rights Reserved.
- xi
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
Revision History
xii -
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
Table of Contents
CHAPTER 1
Introduction
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
Peripherals Covered by this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 2
Typical Users of the LOGIQ C Series . . . . . . . . . . . . . . . . . . . . . . 1 - 2
Safety Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 5
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 5
Human Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 5
Mechanical Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 5
Electrical Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 6
Safe Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 6
Dangerous Procedure Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 6
Returning/Shipping Probes and Repair Parts . . . . . . . . . . . . . . . . . . . . . . . 1 - 6
1 Table of Contents
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
CHAPTER 2
Preparation
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1
Purpose of Chapter 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1
Furnished materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 3
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 3
B/W USB Printer (Sony UP-D897) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 3
Materials supplied with the B/W USB Printer . . . . . . . . . . . . . . . . . . 2 - 3
Materials supplied with scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 3
Color USB Printer (UP-D23MD/HP470) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 4
Materials supplied with the Color USB Printer . . . . . . . . . . . . . . . . . 2 - 4
Materials supplied with scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 4
1 Pedal Footswitch (Whanam FSU2001) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 4
Materials supplied with the Footswitch . . . . . . . . . . . . . . . . . . . . . . . 2 - 4
Materials supplied in the scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 4
Seagate Removable HDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 5
Materials supplied with the Seagate Removable HDD . . . . . . . . . . . 2 - 5
Materials supplied in the scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 5
Peripherals/Accessories Connector Panel . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 5
Rear Panel Connector for LOGIQ C2/C2PRO,LOGIQ C3/C3PRO
and LOGIQ C5/C5PRO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 5
Rear Panel Connector for LOGIQ C3 Premium and
LOGIQ C5 Premium . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 6
Left Panel Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 6
Located on the left side panel is one USB Port. . . . . . . . . . . . . . . . . 2 - 7
1-2 -
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
CHAPTER 3
B/W USB Printer Installation
(Sony UP-D897)
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1
Purpose of Chapter 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1
- 1-3
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
CHAPTER 4
B/W USB Printer Installation
(Sony UP-897MD)
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1
Purpose of Chapter 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1
1-4 -
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
CHAPTER 5
Footswitch Installation
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1
Purpose of Chapter 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1
Configuring Footswtich . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 4
- 1-5
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
CHAPTER 6
Color USB Printer Installation
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1
Purpose of Chapter 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1
1-6 -
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
CHAPTER 7
SanDisk USB Stick Installation
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1
Purpose of Chapter 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1
- 1-7
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
CHAPTER 8
ECG Installation
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1
Purpose of Chapter 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1
1-8 -
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
CHAPTER 9
Seagate Removable HDD Installation
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1
Purpose of Chapter 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1
- 1-9
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
CHAPTER 10
Set up and Check-out
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 1
Purpose of Chapter 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 1
Footswitch Checks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 21
1 - 10 -
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
Chapter 1
Introduction
Section 1-1
Overview
1-1-1 Purpose
This Installation Manual describes how to install and configure the peripherals validated for the
LOGIQ C Series.
NOTE: LOGIQ C series contain LOGIQ C2/C2 PRO,LOGIQ C3/C3PRO,LOGIQ C5/C5 PRO,LOGIQ C3
Premium and LOGIQ C5 Premium.
PAGE
SECTION DESCRIPTION NUMBER
1-1 Overview 1-1
1-2 Important Conventions 1-3
WEIGHT
PART NUMBER DESCRIPTION (KG) POWER CONTROL MODEL
100-120VAC/220-
240VAC
H48112LG Sony B/W USB Printer 3.4 USB ports UP-D897
50/60Hz
1.5A/0.8A
100-120VAC/220-
240VAC
Sony B/W Printer 3.4 UP-897MD
50/60Hz
1.5A/0.8A
H41482LE(CN) 100-120VAC/220-
H48272LR(EU) Color USB Printer 6.5 240VAC USB ports UP-D23MD
H48272LS(US) 1.8A/1.0A
H48242LD(CN) 100-120VAC/220-
H48272LT(EU) Deskjet Color Printer 4.0 240VAC USB ports HP470
H48272LW(US) 1.8A/1.0A
H41852LL
H41852LM ECG USB ports
H41852LK
1-2 -
GE HEALTHCARE LOGIQ C SERIES
DIRECTION 5266280-100, REVISION 3 PERIPHERALS INSTALLATION MANUAL
Section 1-2
Important Conventions
1-2-1 Conventions Used in Book
1-2-1-1 Icons
Pictures, or icons, are used wherever they will reinforce the printed message. The icons, labels and
conventions used on the product and in the service information are described in this chapter.
CAUTION Caution is used to indicate the presence of a hazard that will or can cause minor personal injury
and property damage if instructions are ignored.
NOTE: Notes are used to provide important information about an item or a procedure.
Be sure to read the notes; the information contained in a note can often save you time or effort.
LASER
LIGHT
Other hazard icons make you aware of specific procedures that should be followed.
AVOID STATIC ELECTRICITY TAG AND LOCK OUT WEAR EYE PROTECTION
TAG
&
LOCKOUT EYE
PROTECTION
Signed Date
Section 1-3
Safety Considerations
1-3-1 Introduction
The following safety precautions must be observed during all phases of operation, service and repair of
this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this
manual, violates safety standards of design, manufacture and intended use of the equipment.
Only personnel who have participated in a LOGIQ C Series Training Seminar are authorized to service
the equipment.
• The system is equipped with a three-conductor AC power cable. This must be plugged into an
approved electrical outlet with protective ground. If an extension cord is used with the system, make
sure that the total current rating of the system does not exceed the extension cord rating.
• The power outlet used for this equipment should not be shared with other types of equipment.
• Both the system power cable and the power connector meet international electrical standards.
GEMS policy states that body fluids must be properly removed from any part or equipment prior to
shipment. GEMS employees, as well as customers, are responsible for ensuring that parts/equipment
have been properly decontaminated prior to shipment. Under no circumstance should a part or
equipment with visible body fluids be taken or shipped from a clinic or site (for example, body coils or
an ultrasound probe).
The purpose of the regulation is to protect employees in the transportation industry, as well as the
people who will receive or open this package.
Section 1-4
EMC, EMI, and ESD
1-4-1 Electromagnetic Compatibility (EMC) and Interference (EMI)
Electromagnetic compatibility describes a level of performance of a device within its electromagnetic
environment. This environment consists of the device itself and its surroundings including other
equipment, power sources and persons with which the device must interface. Inadequate compatibility
results when a susceptible device fails to perform as intended due interference from its environment or
when the device produces unacceptable levels of emission to its environment. This interference is often
referred to as radio–frequency or electromagnetic interference (RFI/EMI) and can be radiated through
space or conducted over interconnecting power of signal cables. In addition to electromagnetic energy,
EMC also includes possible effects from electrical fields, magnetic fields, electrostatic discharge and
disturbances in the electrical power supply.
WARNING DO NOT TOUCH ANY BOARDS WITH INTEGRATED CIRCUITS PRIOR TO TAKING THE
NECESSARY ESD PRECAUTIONS:
1.) ALWAYS CONNECT YOURSELF, VIA AN ARM-WRIST STRAP, TO THE ADVISED
ESD CONNECTION POINT LOCATED ON THE REAR OF THE SCANNER (TO THE RIGHT
OF THE POWER CONNECTOR).
2.) FOLLOW GENERAL GUIDELINES FOR HANDLING OF ELECTROSTATIC SENSITIVE
EQUIPMENT.
1-4-3 CE Compliance
The LOGIQ C Series unit conforms to all applicable conducted and radiated emission limits and to
immunity from electrostatic discharge, radiated and conducted RF fields, magnetic fields and power line
transient requirements.
NOTE: For CE Compliance, it is critical that all covers, screws, shielding, gaskets, mesh, clamps, are
in good condition, installed tightly without skew or stress. Proper installation following all
comments noted in this service manual is required in order to achieve full EMC performance.
Section 1-5
Customer Assistance
1-5-1 Contact Information
If this equipment does not work as indicated in this service manual or in the User Manual, or if you
require additional assistance, please contact the local distributor or appropriate support resource, as
listed below.
USA
Service: On-site 1-800–437–1171
GE Healthcare
Ultrasound Service Engineering
Service: Parts 1-800-558-2040
9900 Innovation Drive
Wauwatosa, WI 53226
Applications support 1-800-682-5327 or 1-262-524-5698
Canada 1-800-668-0732
Service 1-800-321-7937
Latin America
Applications support 1-262-524-5698
Europe
GE Ultraschall Deutschland GmbH& Co. KG Phone: +33 (0)130-831-300 (General Imaging and Cardiac)
BeethovenstraBe 239
Postfach 11 05 60, D-42665 Solingen Fax: +49 (0)212-2802-431
Germany
Asia (Singapore)
Tel: +65 291-8528
GE Ultrasound Asia
Service Department - Ultrasound
298 Tiong Bahru Road #15-01/06
Central Plaza
Fax: +65 6291-7006
Singapore 169730
Phone: 81-42-648-2944
Japan Support Center
Fax: 81-42-648-2905
Chapter 2
Preparation
Section 2-1
Overview
2-1-1 Purpose of Chapter 2
This chapter includes procedures to conduct before installation of the Peripherals.
Section 2-2
Power Shut Down
Press the ON/OFF key on the Control Panel once to display the LOGIQC2/C2PRO/C3/C3
System - Exit Menu on the monitor. PRO/C5/C5PRO
Section 2-3
Furnished materials
2-3-1 Overview
This section describes the materials furnished with the Peripherals and with the System.
Retain the original carton and packing materials in case transport is needed in the future.
2. Paper Roll 1
3. Operating Instructions 1
4. USB cable 1
6. Printer Bracket 1
7. Printer_Bracket_Cushion 4
8. D2 Screw SJ2836-87 M3X8 4
Table 2-4 B/W USB Printer: Materials furnished with the Scanner
2. Paper Roll 1
3. Operating Instructions 1
4. AC Power Cord 1
5. USB cable 1
Table 2-6 Color USB Printer: Materials furnished with the Scanner
2. USB Cable 1
Table 2-10 Seagate Removable HDD: Materials furnished with the scanner
2-3-6-1 Rear Panel Connector for LOGIQ C2/C2PRO,LOGIQ C3/C3PRO and LOGIQ C5/C5PRO
Located on the rear panel are Network port, 2 USB port, S-Video Out, VGA, Audio Out, Composite Out.
2-3-6-2 Rear Panel Connector for LOGIQ C3 Premium and LOGIQ C5 Premium
5 6
NOTICE Power on LOGIQ C Series to work first, then connect USB devices and power on USB devices.
NOTE: Each outer (case) ground line of peripheral/accessory connectors is protectively grounded.
Signal ground lines are not isolated.
Chapter 3
B/W USB Printer Installation
(Sony UP-D897)
Section 3-1
Overview
3-1-1 Purpose of Chapter 3
This chapter describes the installation procedure for the Sony UP-D897 B/W USB Printer.
Section 3-2
Installing the B/W USB Printer
3-2-1 Tools
No special tools needed.
3-2-2 Manpower
One person 5 min.
3-2-3 Preparations
1.) Unpack the B/W USB Printer.
NOTE: The side with 2 juts is the back of Printer Bracket, the Printer Bracket Cushions should be stuck
on the back of Printer Bracket; the Printer should be fixed on the front of the Printer Bracket.
3
1
4 2
2 1
3 4
4.) Connect the Power cord and USB Cable to the Printer Box and B/W printer, refer to Figure 3-
4 on page 3-3
USB Cable
Power Cable
5.) Put the B/W Printer into the Printer Box, refer to Figure 3-5 on page 3-4
NOTE: When putting the B/W Printer into the Printer Box, the jut of the Printer Bracket should be put in
corresponding hole in the Printer Box, which will let B/W Printer fit well.
Chapter 4
B/W USB Printer Installation
(Sony UP-897MD)
Section 4-1
Overview
4-1-1 Purpose of Chapter 4
This chapter describes the installation procedure for the Sony UP-897MD B/W Printer.
B/W Printer
Figure 4-6 B/W Printer Connection for LOGIQ C3 Premium and LOGIQ C5 Premium
NOTE: Sony UP-897MD B/W Printer is only available for LOGIQ C3 Premium and LOGIQ C5 Premium.
Section 4-2
Installing the B/W Printer
4-2-1 Tools
No special tools needed.
4-2-2 Manpower
One person 5 min.
4-2-3 Preparations
1.) Unpack the B/W Printer.
2.) Connect the Power Cable to AC IN Port of the Printer and the Electric Outlet, refer to Figure 3-2 on
page 3-2
Chapter 5
Footswitch Installation
Section 5-1
Overview
5-1-1 Purpose of Chapter 5
This chapter describes how to install Footswitch. LOGIQ C Series supports 1-pedal footswitch and 3-
Pedal footswitch.
Section 5-2
Installing Footswitch
5-2-1 Tools
No special tools needed.
5-2-2 Manpower
One person 5 min.
5-2-3 Preparations
1.) Unpack the Footswitch.
2.) Ensure no physical damage.
1-pedal
Footswitch
3-pedal
Footswitch
Section 5-3
Configuring Footswtich
Footswtich supports five configurations: Non function, acting as Freeze button, Print button, Store
button or B pause button.
NOTE: Acting as B pause button configuration of footswitch is not supported by LOGIQ C2/C2 PRO.
The default setting is acting as Freeze button; To change them, press Utility button on the key board
then select Application-->Settings. (see the figure below)
NOTE: The footswitch function is in Middle, please ignore the Left and right.
Chapter 6
Color USB Printer Installation
Section 6-1
Overview
6-1-1 Purpose of Chapter 6
This chapter describes the installation procedure for Color USB Printers. LOGIQ C Series supports two
types of printers for printing: Sony UP-D23MD Digital Color USB Printer, HP470 Deskjet Color Printer.
NOTE: Color Printer Sony UP-D23MD is only supported by LOGIQ C5/C5 PRO and LOGIQ C5
Premium; HP470b printer is supported by LOGIQ C2/C2 PRO, LOGIQ C3/C3 PRO ,LOGIQ C5
/C5 PRO,LOGIQ C3 Premium and LOGIQ C5 Premium.
For this two type printers, the connection to LOGIQ C Series is same. Here we take HP470b Deskjet
Color Printer as an example. Please make sure the printers are Power On.
Section 6-2
Installing the Color USB Printer
6-2-1 Tools
No special tools needed.
6-2-2 Manpower
One person 5 min.
6-2-3 Preparations
1.) Unpack the color USB Printer.
USB cable
Power cord
3.) Connect power cord and USB cable to the system as shown in Figure 6-15 on page 6-2
NOTE: The Color Printer Power cable should be connected to the Output Port on the Power Box.
USB cable
Power cord
Section 6-3
Setting for B/W and Color printer concurrent working
Example below points B/W printer (UP-D897) to print button on the keyboard and Color printer (HP470)
to Store button.
1.) Power on LOGIQ C Series system and wait until the system booting up.
1.) Connect B/W printer with USB ports of LOGIQ C Series and power on printer.
2.) Choose [Utility] -> [System] -> [Peripherals], press [Printer] button, then check the highlight printer
-- Sony UP-D897.
Section 6-3 Setting for B/W and Color printer concurrent working (cont’d)
3.) Choose [connectivity] -> [Service], select [Standard Print] in list, see Figure 6-18 on page 6-4 .
4.) Set standard printer as “Sony UP-D897”, change the name as “UP-D897” in properties area. Save
the setting.
5.) Choose [Connectivity] -> [Button], Select [Print] in Button list, and then press “<<“ to remove all the
original setting.
Section 6-3 Setting for B/W and Color printer concurrent working (cont’d)
6.) Select Sony UPD897, press “>>” to add to the Printflow View.
7.) [Print] setting for UP-D897 shows as below.
8.) Connect Color printer (HP 470b) to the USB ports of LOGIQ C Series.
9.) Power on the Color printer.
10.)Choose [connectivity] -> [Service], select [Standard Print] in list, see Figure 6-21 on page 6-5 .
11.)Set standard printer as “HP Officejet H470 Series”, change the name as “HP Officejet H470 Series”
in properties area. Save the setting.
Section 6-3 Setting for B/W and Color printer concurrent working (cont’d)
12.)Go to [Connectivity] -> [Button], choose [Store], and then remove all the [Store] original setting.
Chapter 7
SanDisk USB Stick Installation
Section 7-1
Overview
7-1-1 Purpose of Chapter 7
This chapter describes the installation procedure for SanDisk USB Stick.
Section 7-2
Installing the SanDisk USB Stick
7-2-1 Tools
No special tools needed.
7-2-2 Manpower
One person 1 min.
7-2-3 Preparations
1.) Unpack the SanDisk USB Stick
Chapter 8
ECG Installation
Section 8-1
Overview
8-1-1 Purpose of Chapter 8
This chapter describes the installation procedure for the ECG.
NOTE: Only LOGIQ C5/C5 PRO and LOGIQ C5 Premium supports ECG.
Section 8-2
Installing the ECG
8-2-1 Tools
No special tools needed.
8-2-2 Manpower
One person 1 min.
8-2-3 Preparations
1.) Unpack the ECG.
2.) Ensure no physical damage (refer to Figure 8-27 on page 8-2 ).
3.) Wait 5 seconds for ECG function start automatically. (Refer to Figure 8-29 on page 8-3 ).
AHA IEC
RA R
I Right Arm
(White) (Red)
LA L
II Left Arm
(Black) (Yellow)
RL N
III Right Leg
(Green) (Black)
Feature Specification
Current 80 mA ± 10%
CMMR > 80 dB
Chapter 9
Seagate Removable HDD Installation
Section 9-1
Overview
9-1-1 Purpose of Chapter 9
This chapter describes the installation procedure for Seagate Removable HDD.
Section 9-2
Installing the Seagate Removable HDD
9-2-1 Tools
No special tools needed.
9-2-2 Manpower
One person 1 min.
9-2-3 Preparations
1.) Unpack the Seagate Removable HDD.
Chapter 10
Set up and Check-out
Section 10-1
Overview
10-1-1 Purpose of Chapter 10
This chapter describes the Final Setup for the Peripherals and the Operational Check-out.
Section 10-2
B/W USB Printer
10-2-1 Control assignment for B/W USB Printer
The B/W USB Printers are controlled from the Print on the System’s Control Panel. The factory setting
is Print for all USB Printer.
Figure 10-1 The Utility window (with the General/System sheet displayed)
Figure 10-2 The Connectivity window (with the Connectivity/Service sheet displayed)
5.) Select CONNECTIVITY and then choose BUTTON in the upper menu (see Figure 10-
3 on page 10-3 ).
6.) In the Button Field, select the Control Panel Key to configure: Print.
7.) Select Standard Print, press “>>” to add to the Printflow View. (see Figure 10-3 on page 10-3 )
Figure 10-3 The Connectivity window (with the Connectivity/Button sheet displayed)
Section 10-3
HP 470 office jet Printer
10-3-1 Control assignment for HP 470 officejet Printer
The HP 470 officejet Printer are controlled from the Print on the System’s Control Panel. The factory
setting is Print for all USB Printer.
Figure 10-4 The Utility window (with the General/System sheet displayed)
4.) Choose [Connectivity] -> [Service], select [Standard Print] in list, see Figure 10-6 on page 10-9 .
5.) Set standard printer as “HP Officejet H470 Series”. Save the setting.
8.) In the Button Field, select the Control Panel Key to configure: Print (see Figure 10-8 on page 10-10
).
9.) Select Standard Print, press “>>” to add to the Printflow View.
10.)If another device is selected, use “<<“ to clear window.
Section 10-4
Sony UP-D23 MD Printer
10-4-1 Control assignment for Sony UP-D23 MD Printer
The Sony UP-D23 MD Printer are controlled from the Print on the System’s Control Panel. The factory
setting is Print for all USB Printer.
Figure 10-9 The Utility window (with the General/System sheet displayed)
4.) Choose [Connectivity] -> [Service], select [Standard Print] in list, see Figure 10-6 on page 10-9 .
5.) Set standard printer as “Sony UP-D23MD”. Save the setting.
8.) In the Button Field, select the Control Panel Key to configure: Print (see Figure 10-8 on page 10-10
).
9.) Select Standard Print, press “>>” to add to the Printflow View.
10.)If another device is selected, use “<<“ to clear window.
The following digital printer is supported by LOGIQ C5/C5 PRO: UP-D23MD Sony printer.
Section 10-5
B/W USB Printer Checks
Make sure Printer Function is assigned to Print key. (The factory default is Print for all USB Printer.)
When scanning in B mode, press “Freeze” to Image scanning stops with the last picture on the
1
stop image acquisition screen.
Section 10-6
Color Printer Checks
Make sure Printer Function is assigned to Print key. (The factory default is Print for all USB Printer.)
When scanning in B mode, press “Freeze” to Image scanning stops with the last picture on the
1
stop image acquisition screen.
Section 10-7
Footswitch Checks
Table 10-1 Footswitch Checks
Section 10-8
USB Stick Checks
Table 10-1 USB Stick Checks